First you remove the lower back seat, and the bolts that secure the upper will be exposed. Remove them and lift out upper back seat.
In the back of the seat (both) you have a star screw bit that one you remove it you lift up on the back of the seat and the front will come up out of a groove that it slides into.
To remove the bottom back seat on a 2001 Cavalier, open all the doors and pull the front seats forward. Next, remove the seat cushion from the vehicle.
Move the seat all the way forward then remove the nuts or bolts from rear. Move the seat all the way back then remove the front nuts or bolts. Tip the seat back and disconnect the electrical plug(s). Remove the seat from vehicle.
pull front of rear seat up. remove it and battery is right there
It is located under the back seat in the middle. You should be able to just lift the back seat up and off.
Remove the bolts fastening the rear seat cushion (Figure 7.52).Remove the rear seat cushion assembly.Remove the screws and remove the side rear seat back (Figure 7.53).Remove the lower bolts fastening the rear seat back.Tightening torque - 17-26 NmFlip forward the rear seat back, remove the bolts and remove the back seat.Tightening torque - 17-26 Nm
under the back seat! Under the back seat
No you can not. You will have to remove the gas tank.
remove back seat then pull out and remove from mounting tray then that's it
just pull up on it from the front of the seat it will pop out of the holders then un bolt the back of the bracket
there are two bolts in the back of the seat. remove them and then slide the seat back about an inch and remove
On my 2001 Astro there are 4 bolts from the seat frame to the floor remove the bolts and the seat is removable (HINT move the middle passenger seat back as far as it can go and that is easier to remove the seat and frame ..I have done this twice on the 2001 and 3 times on the 1989 I had..
Underneath the back seat
how to remove 2004 scion back seat
The bolts are visible at the base of the seat. Remove them and lift out the seat.
To remove the back seat of a Skylark, reach into the area between the back and the seat and pull up on the seat. The back part of the seat is bolted in and will require a socket wrench to remove.
In my 2000 LeSabre, it's under the back seat. Remove the rear seat and I'll bet it's there.
well the first thing is to remove the lower seat. It has two clips near the front of it . Remove the lower seat now. Next remove the side panel right above the back seat. Now you have to remove the bolts for the seat belts, it holds the back part of the seat in. move the back part of the seat up towards the back window. You should hear the seat come loose. Now when you put the seat back in don't forget to pull the seat belts back though.
To remove the back seat of a 1998 Toyota Corolla, you will need to remove the carpet to expose the bolts for the seat. Then, loosen the bolts by removing the nuts. You can then remove the seat.
remove back seat jeep
You need to take the back seats out. The lower part of the seat just presses in at the front. Where your ankles would be if you are sitting in the seat. Once you get that out you can see the bolts that hold the top/ back in.
To remove a fixed rear seat on a 2001 Grand Am, you need to remove the two bolts in the lower portion of the seat back. Grab the bottom of the seat back and lift to disengage the clips that secure the upper part of the seat. Finally, move the passenger and driver seat belts behind the seat and remove the seat from the vehicle. If you have a split folding rear seat, you need to open the truck and pull the left and right straps to unlock the seat backs. Fold them down and undo the small hook latch from the pivot bolt. Lift the seat to clear the pivot bolt from the latch. Finally, pull seat toward the center of the car to disengage the outer pivot bolt and remove seat from vehicle.
the back of the seat is the front of the trunk. To remove the rear seat back you first have to remove the two bolts just under bottom seat assembly. Bolts are located at the botton of lower seat, about between your ankles if you were sitting in the seat, one on each side. Then remove bottom seat assembly. Then remove seatbelt bolts that hold seat back assembly, lift straight up on seat back and remove.
To remove the back seat on a 1989 Ford Thunderbird, the first step is to remove the back of the seat. The back is held in by bolts on each side. After the back is removed, the seat area should come out after removing the floor bolts.