answersLogoWhite
Chevy Cavalier
Chevy Silverado
Chevy Beretta

How do you remove the backseat of a Chevy beretta?

212223

Top Answer
User Avatar
Wiki User
2007-01-29 03:30:44
2007-01-29 03:30:44

On a 96 beretta there are 2 bolts just under the front edge of the seat. Then after you remove the seat bottom there are 2 torx bolts (don't remember the size)holding the seat back and seat belts. After you remove the 2 torx bolts then you pull the seat back up to unhook the top of the seat back. torx T50

1

Related Questions

User Avatar

i would like to remove the backseat from my 1992 chevy cavalier

User Avatar

to take out the rear speakers in a 1995 Chevy Beretta you need to remove the plastic molding on the inside of the passenger compartment in the backseat area of the car, and pull the backseat forward to get to that rear deck by the window. you will also need to remove the rear brake light in the window. when installing new speakers it is a good idea to cut the fabric so that you can get to the speakers much more easily if you need to remove them again.

User Avatar

how to replace a 1990 Chevy Beretta battery

User Avatar

NO. You must remove the fuel tank to service the fuel pump.

User Avatar

i have a 1994 Chevy beretta and they are under the engine

User Avatar

First, you must move your backseat and remove it from the vehicle, then you use the correct tool to correctly remove the rear speakers. It is very time consuming.

User Avatar

There are five steps on how to remove the back seat in a 1997 Chevy Malibu. Some of the step-by-step instructions are open the trunk lid, pull the top portion of the backseat all the way down, and then pull the top portion of the backseat all the way down and locate the hinges from which the seat pivots.

User Avatar

Does anyone know of any chevy beretta cam shaft problems?

User Avatar

how to change third or center brake light on Chevy beretta 95

User Avatar

There are no rear struts in the Chevy Beretta. Only shocks.

User Avatar

the beretta and lumina motors are about the same i have a lumina motor in my 95 beretta

User Avatar

Unbolt it from the body.

User Avatar

Ebay. Just enter Chevy Beretta under parts and accessories

User Avatar

you may have to remove the intake from the block and then use an extractor tool to remove the rest. then replace the connector.

User Avatar

depends on engine, mounting, body, ecm, and about a million other things, but possibily

User Avatar

can someone give me a diagram of a fuse box location for a 1993 Chevy beretta

User Avatar

junk the car a new starter and labor is worth more than the book value of the car

User Avatar

Hi there, there should be four screws inside the centre console if you undo them your well away :)

User Avatar

Yes it will, but you have to put all the blazer engine stuff onto the beretta engine...

User Avatar

The answer depends on the size of the people and how comfortable they wish to be. The Chevy Cobalt has two front seats and a backseat which has 46.1 inches of hip room. The Chevy Cobalt's backseat has been described as "small" in the past.

User Avatar

I am trying to find the 1988 chevy beretta computer module and where is it located?

User Avatar

Hello. I have a 2011 Chevy Impala and the backseat middle headrest prevents good visibility and, thus, is a driving safety concern. Do you have any suggestions? Thank you! Hal

User Avatar

Remove the glove box and look under the dash. You should see a big metal box. That's it.

User Avatar

NEED help is there a diagram with the bolts in the backseat of a 1998 chevy cavalier?

User Avatar

its not removeable, it just slides


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.