0
How do you remove the camshaft position sensor on a 2002 Hyundai sonata 4 cylinder?
Wiki User
∙ 14y ago
Crankshaft position sensor is around $98.00 for dealer part...labor around $270.00...cost can increase substantially if timing belt is replaced ( since your in there ) belt tensioner, possible water pump...depending how many miles on engine and if you plan on keeping car...could hit $1000.00 plus
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Where is the Camshaft Position Sensor located on a 2002 Hyundai Sonata V6?
The camshaft position sensor on your 2002 automobile is located on the front of the camshaft. You will need to remove the front engine cover to access the sensor.
How do you change camshaft position sensor 2007 f150?
Remove ignition transformer to reach it. There should be 2 camshaft position sensors on the 5.4L engine - visibly on the front right cylinder head and the other visibly on the front of the left cylinder head. Remove ,Replace, then return ignition transformer.
Where is BMW Z3- 1.9 camshaft position sensor located?
small sensor on front of cylinder head. connected under manifold,must remove manifold.
Must you remove the camshaft to replace the timing belt of a 1989 Chevy Celebrity 4-cylinder?
no The Chevy Celebrity 4 cylinder engine doesn't use a timing belt, it uses a timing gear. To replace the gear it is necessary to remove the camshaft from the engine as it is a press job. To remove the camshaft it is necessary to remove the engine from the car.
How do you replace replace the camshaft position sensor?
In order to replace the camshaft position sensor, you would need to disconnect the electrical plug holding it in. Using a socket, hold down the bolt and remove the camshaft position sensor.
Where is the camshaft position sensor located on a 1999 Dodge Durango?
It's located on the distributor. You don't have to remove the distributor to replace the sensor. Remove the air cleaner, disconnect the negative battery cable, remove the distributor cap, disconnect the camshaft position sensor wiring harness, remove the distributor rotor, lift the camshaft position sensor assembly from the distributor housing Camshaft Position Sensor. Installation, Install the camshaft position sensor into the distributor. Align the sensor into the notch on the distributor housing, connect the wiring harness, reinstall the rotor, reinstall the distributor cap. Tighten the mounting screws, reinstall the air cleaner.
Where is the camshaft sensor on a dodge ram 1500?
3.9L, 5.2L, 5.9L the camshaft position sensor is located under the distributor cap you have to remove it carefully and it will go only one way. 3.7L, 4.7L it is under the front outside of the passenger side cylinder head
Where is the camshaft position sensor on a 1999 Dodge Neon and hw do you replace it?
The camshaft position sensor on the Neon 4 cylinder is located at the driver's side of the head in line with the camshafts, just below the valve cover. It's easy enough to replace...simply disconnect the wiring connector, remove the attachment bolts and remove the sensor. Make sure you replace the gasket as well...failed gaskets here are often mistaken for cylinder head oil leaks. Hope this helps!
Where is the cam position sensor on a jaguar xj8?
how do you remove camshaft sensor on jaguar xj8
Where is the camshaft position sensor switch located on your 1995 Durango?
The Dodge Durango was introduced in 1998, so this question cannot be answered. However, in the 2000 Durango.... The camshaft position sensor is located in the distributor on all 3.9L V-6 and 5.2/5.9L V-8 engines Camshaft Position Sensor REMOVAL Distributor removal is not necessary to remove camshaft position sensor Remove air cleaner assembly. Disconnect negative cable from battery. Remove distributor cap from distributor (two screws) Disconnect camshaft position sensor wiring harness from main engine wiring harness. Remove distributor rotor from distributor shaft. Lift the camshaft position sensor assembly from the distributor housing Camshaft Position Sensor INSTALLATION Install camshaft position sensor to distributor. Align sensor into notch on distributor housing. Connect wiring harness. Install rotor. Install distributor cap. Tighten mounting screws. Install air cleaner assembly. (this info from post on answers.com about cps on 2000 durango)
What size socket do you require to remove cylinder head bolts on a Hyundai coupe v6?
10mm
How do you replace a 2001 Hyundai sonata 6 cylinder alternator?
is there a quick way to remove alternator
