There are two 11 mm nuts holding turn signal which in turns holds the chrome piece also in place. There are two holes in the core support which they are hiding. Open Hood To Locate On Interior side of Core Support.
Open hood, look at headlamp assembly. There will be large white/tan cover. Turn cover clockwise to remove. Turn the headlamp assembly c-clockwise and remove.
If it is similar to my Bravada there are 2 clips that hold the entire assembly in place Lift these clips and lift out assembly then remove flexible plastic cover and bulbs are accessible
Well you can take two approches to changing the headlamp bulbs. First, although it is a tight fit you can pop the hood. remove the black plastic guards(for lack of a better word) you will see what im talking about, and reach your hand in the rear of the head lamp, remove the rubber cover and pull the bulb out and change. Another way is to remove the grille, and trim that fits underneath the headlamp, and remove the whole headlight assembly. it is alot easier to see what you are doing with the headlamp assembly removed
You'll need a torx bit from the parts store. Its easy to remove the cover around the lights and the chrome cover around the single light. Don't mess with the springs or you will have to reset you beam alinement.
the headlamp assembly needs to be removed. remove the 3 "scrivets" in the top of the grill and remove grill. remove 2 x torx headed screws in the top of the headlamp and 1 Philips headed screw that is alongside the headlamp behind a small plastic hinged door. headlamp can now be removed and the relevant cover removed to access the bulb.
You must stop the headlight in the up position. Sometimes you have to do this manually, with the over-ride on the headlamp motor.It's best to do this with the hood up. There are two screws in front of the headlamp on the bottom that must be removed. Then turn the assembly to the partially down position to remove two more screws; one on either side toward the rear of the assembly. This will enable you to remove the cover. Then simply remove the screws that hold the chrome frame around the bulb and replace. Reverse procedure for install. CAUTION: be sure not to mistake the adjustment screws for the retaining screws, as your headlamps will be out of allignment. when the headlight is up..or {on position}..it can be changed.. !!!!
remove the black plastic radiator cover (push-pins) then remove the two bolts holding the headlamp in unplugh the bulb harness and remove mess around with the screws and clips on the headlight assembly, but i dont know if you can take the front clear plastic piece off. (and be able to put it right back on..)
located behind the bumper cover under headlamp assembly
To remove the bulb- raise hood reach behind headlight housing grasp the bulb holder assembly and rotate counterclockwise and gently pull straight out.There are two bulbs to each headlight assembly. Note.... do not touch the new bulb lense with your fingers.The oil in your skin will cause a hole to burn in the halogen bulb. If you do touch the bulb,clean with alcohol before installing. To remove the headlamp assembly- Raise the hood and remove bumper cover screws and remaining bumper cover screws.Then remove the electrical connection from the back of assembly.Then remove the 4 screws retaining the head lamp assembly and remove the assembly.
1. Open and prop up hood. 2. Release clamping latch on side of headlamp housing, then rotate locking ring upwards. 3. Slide the headlamp assembly forward out of the housing. 4. Release latch on the black cover at the rear of the headlamp assembly and remove same. 5. Remove the wire connector from the rear of the bulb, flip up locking lever, and remove the spent bulb. 6. Reassemble in reverse order. Quick, easy, and does not require the removal of the battery and electrical package.
Best done cold. from under the hood, there are to metal clamps on the back of the headlamp assembly and remove the cover then replave the bulb, on the driver side you can remove the battery for ease
Best done cold. from under the hood, there are to metal clamps on the back of the headlamp assembly and remove the cover then replave the bulb, on the driver side you can remove the battery for ease