0
How do you remove the clutch cable from the bulkhead in a citroen relay van?
Wiki User
∙ 14y ago
Hi there
Probably too late but you never know! Changed mine after it broke and it simply slides thru the bulkhead with the rubber grommi attatched, inside to out. Takes a bit of oushing and heaving but not too bad. Cheers.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you replace a clutch cable for a 1990 Nissan sentra?
# Remove the cover from under the facia panel # Release the nuts at the end of the cable at the release lever and disconnect the cable from the lever # Working from the inside of the car remove the clevis pin and disconnect the cable from the clutch pedal arm # Unscrew the two nuts which retain the cable grommet to the bulkhead and withdraw the cable from the car
Your citroen berlingo clutch cable keeps snapping?
The clutch cable for the Citroen Berlingo could be snapping due to a sharp turn in the cable, or due to the clutch having a problem. Make sure that the clutch is operating smoothly, and the cable does not have any tight turns that might cause a kink in the system.
How do you fit a clutch cable on a 1995 Rover 218?
R65 type transmission. Remove the air cleaner. Working in the engine compartment slide the clutch cable and fitting from the clutch release lever on the top of the gearbox. Release the cable sheath grommet from the bracket on the gearbox. Working in the drivers footwell release the 3 securing clips and remove the fusebox cover. Release the securing clips and remove the driver's side lower fascia panel . Reach up behind the fascia and unhook the end of the clutch cable from the pedal. Working in the engine compartment pull the cable through the bulkhead. Note cable routing and release the cable from any other retaining clips. Refitting Lubricate the cable bulkhead bush with rubber grease. Route the cable through the engine compartment and throught the bulkhead. Working in the drivers footwell reconnect the cable to the foot pedal then push the rubber bush on the cable fully into the bulkhead tube until the steel washer on the cable seats on the tube. Pull the clutch lever through its full range of movement to set the cable self adjustment mechanism. PG1 type transmission Remove air cleaner. Jack up front of vehicle onto axle stands. Working in the engine compartment slide the clutch cable and fitting from the clutch release lever on the top of the gearbox. Release the cable sheath grommet from the bracket on the gearbox. On right hand drive models release the cable from the clip attached to the coolant hose. Rest as for R65
How do you change a clutch cable on a J Reg Cavalier 2.0 SRI?
For access,if fitted remove electrical relay box,(3 bolts)and lay aside,remove hydraulic oilreservoir(1 bolt)and lay aside upright. Measure thread length of inner cable thru the adjuster on clutch arm and note it. Remove retaining clip and cable from clutch arm. In car,remove return spring and cable hook from pedal. Remove cable assembly from bulkhead pulling thru engine compartment. Push new cable thru bulkhead and reconnect cable and return spring to pedal. Fit cable inner to clutch arm and reset thread to noted length. Back in car,measure distance from top of clutch pedal pad to rim of steering wheel,then depress clutch fully and remeasure.Difference should be 134 to 141mm on rhd car.Adjust at clutch arm to correct it. LHD is 129 to 130mm. When dimension is correct,refit retaining clip on clutch arm. Note Clutch pedal correctly set will be higher than brake and have no free play. Refit relay box and hydraulic res.
How do i Refill the clutch oil on a citroen xsara 2.0 hdi?
Xsara don't use hydraulic clutch. It has a cable.
How do you remove the gearshift cables on a citroen dispatch?
replace gear shift cable citroen dispatch
How do you remove the clutch cable on a 1996 Chevy s10?
There is no cable, it is hydraulic operated.
How do you change the clutch cable on a 1995 Neon?
First, the clutch cable is self adjusting, don't pull on the clutch cable housing to remove it from the dash panel, the self adjuster may be damaged. Remove the power distribution center and the transaxle cover. Pull back on the clutch cable housing and disconnect the cable. Pull the cable from the slot in the transaxle and disconnect the cable from the release lever. Push in the clutch cable and remove the cable from the pedal. Pull the cable from the dash using a slight twisting motion. Installation is the reverse proceedure. You may want to get a manual for all the 8x10 glossy photos and stuff.
How do you remove 2001 Hyundai tiburon clutch release bearing?
at the end of the clutch cable remove nut from the top of that arm pull that arm off.
How do you fit a new clutch cable to a Vauxhall Corsa X reg?
Check and record the thread length of the old cable found sticking out of the adjuster block on the clutch arm. Remove the securing clip and remove cable from the arm.Inside the car,unhook the cable end from the pedal. Pull the cable out of the bulkhead from the engine side,push the new one in the same way and hook on to pedal.Make sure the cable follows the same routing as the old one,no tight bends no chafing.Connect up to clutch arm and set threads to saved measurement,this will be somewhere near right. Inside car,measure distance from steering wheel rim to pedal and note it.Then depress clutch fully and re-measure the steering wheel to pedal distance. The difference between the two measurements should be 126mm to 132mm.If not correct,adjust the cable adjuster on clutch arm a turn at a time and recheck. You may go the wrong way first time,it's a bit trial and error.NOTE When correctly set up,the brake pedal and clutch pedal will be not be parallel,the clutch pedal will sit a bit higher.Lastly,refit the securing clip to the cable on the clutch arm.
How to remove clutch cable for a 2006 wide glide harley?
1. Take the tension out of the cable by loosening the adjustment on the cable. 1/2" and 9/16" wrench required. 2. Take the Allen screws out of the right side transmission cover. (may have to remove exhaust to do so. 3. Remove C-clip holding clutch mechanism inside the trans cover. 4. Remove cable from clutch mechanism and unscrew cable from trans cover. 5. Remove pin on handlebar lever and remove cable from lever. To install reverse removal instructions ***Note*** Be careful when threading new cable into trans case. DO NOT over tighten you will break the new cable
How do you change the clutch cable in a 1990 suzuki vitara?
go under the car with a 14mm spanner and undo the adjustment nut, also undo the nut that passes thru the clutch lever (sticks out the side of the gearbox) Slide the end of the cable out of the fork, and then remove the 14mm locking nut that holds the sheath of the cable in postition. This completes the 'clutch' size of the cable. Then using a 10mm spanner remove the 2 bolts/nuts in the engine bay where the clutch cable run into the cabin. In the drivers footwell stick your hand up and unhook the hook on the end of the cable off the top of the clutch pedal. Install is reverse of removal but requires you to tighten the clutch cable by tightening the nut on the clutch end of the cable. (you will know when you see it)
