Ford Ranger XLT
Grand Am SE
Pulleys

How do you remove the crank shaft pulley on a Grand Am SE?

262728

Top Answer
User Avatar
Wiki User
2005-10-24 04:07:20
2005-10-24 04:07:20

its located on the front passenger side of the car.first take off the tire,then the inner fender and the crankshaft pulley will be right there. its also easier to do with air tools.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

To remove a crank shaft pulley you need to first jack up the car. Next, remove the bold holding the crack shaft pulley in place and remove the unit. Reverse direction to put the new crank shaft pulley on your car.

User Avatar

how to get the crank shaft pulley off of a 03 Hyundai elanta GLS

User Avatar

A video instruction guide on how to check a crank shaft pulley can be seen on YouTube. Just type in "How to check crank shaft pulley", click on Search, then play the first video.

User Avatar

To the right of the crank shaft pulley. You should see a single black wire going up from the pulley. All you need is a 10MM socket to remove it.

User Avatar

disconnect the battery, remove the bolt in the center of the pulley, then use a harmonic balancer tool to remove it

User Avatar

You have to get a pulley puller of the appropriate size. Without a pulley you have no chance safely to remove it. Be careful do not deform the pulley it's not that hard as you can think.

User Avatar

Im not sure which direction the bolt turns to remove the pulley...the crank shaft turns in clock wise direction when engine is running.

User Avatar

After removing the right front tire and fender liner, you remove the serpentine belt. You then remove the crank bolt and use a puller to remove the pulley.After removing the right front tire and fender liner, you remove the serpentine belt. You then remove the crank bolt and use a puller to remove the pulley.

User Avatar

It is on the front of the crank shaft and under the timing belt cover. You have to remove the crank pulley and all the belts and then the lower timing cover. It is not a job for a beginner.from : http://repairpal.com/crankshaft-sensor-569

User Avatar

Honda Crank Pulley Tool 50mm. The part number is 646796 at DenLorsTools.com. There is a video that shows it in use.

User Avatar

How do I remove a pully from the drive shaft. The snap ring that holds pully on has been taken off.Itried a gear puller but it bends the pully.

User Avatar

Use an easy-out of harder metal after drilling a small hole with harder metal.

User Avatar

It is on the front of the crank shaft. It seals the oil at the crank pulley.

User Avatar

It's behind the timing belt cover on top of the crank pulley.

User Avatar

remove 22mm center bolt its regular thread there are 2 threaded holes in pulley you will need the right pulley remover with the right bolts for the pulley you can get this at most parts stores make sure to not mess up crankshaft bolt threads

User Avatar

This what you are looking for?>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>

User Avatar

No, it's bolted to the end of the crank which pistons/rods attached to.

User Avatar

The 5.3 liter Vortec Engine on the 2000 Chevy Silverado has a tapered crank shaft. The crank pulley has no woodruff key, is not indexed and is pressed on.

User Avatar

cam shaft pulley mark to head /crank shaft pulley mark to oil pump housing mark

User Avatar

For the 3.3 & 3.8L, it is on the pass-side before the crank-shaft.You can access it from above.Remove tension from the belt.Use a 10mm short socket to remove bolts from pulley .remove bolts attaching pump to block.Replace as directed.Pretty simple fix.GL

User Avatar

under the crank pulley, right side of car under front of engine


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.