0
How do you remove the differential from the housing on an 8.8 ford axle?
Wiki User
∙ 15y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Where is rear axle housing Ford Ranger 1999?
Between the 2 back wheels , in the center (differential housing) where the drive gears are
How do you remove the right front axle shaft out of the differential on a 1992 ford F150 4x4 with a 5.8L?
How to remove the right side axle half on a 1995 f150
Velocity speed sensor Where is it located in 1998 ford escort sedan?
it's on top of the differential, which is on the driver's (U.S.) side just behind the transmission (the axle goes directly from the wheel into the differential and the speed sensor is on top of the differential housing).
How do you remove the axle shaft from the front differential on a Ford F-250?
Just pull it out. There should be nothing holding it in the differentail after you remove the locking hub and the hub.
Where is the bolt located to fill the rear axle for a 96 ford bronco?
plug is on the left front of axle housing. take a 3/8 drive to remove
How do you remove rear axle F250 Ford?
how to remove rear axle from 1988 f250 ford
How do you fix a ford F-150 4x4 rear wheel bearing?
access the rear differential, and remove cover.remove 5/16 bolt and remove pin holding axle in. with wheel and drum off, push axle in to reveal c-clip inside differential. once c-clip is removed, pull axle out of axle housing. remove axle seal with seal puller to access bearing. bearing must be removed using apropriate tools(bearing puller, slide hammer, etc..). install new bearing with bearing driver. install new seal with seal driver. reinstall remaining parts in reverse order.
Diagram for ford f250 diesel truck front axle?
drawing for bearings and seals of front differential axle
What is ford axle code H6?
( H6 ) - is a 3.73 limited slip differential on a Ford truck / SUV
What ratio is ford axle code H6?
( H6 ) - is a 3.73 limited slip differential on a Ford truck / SUV
What is ford axle code C9?
I believe that is a limited slip differential with 3.55 gears
How do you remove rear axle of 1999 ford expedition?
Rear Axle Axle Shaft, Bearing and SealRemoval & Installation Ford 8.8 Inch and 9.75-Inch Ring Gear # Raise and safely support the vehicle on jack stands. # Remove the wheels from the brake drums. # Place a drain pan under the housing and drain the lubricant by loosening the hosing cover. # Remove the locks securing the brake drums to the axle shaft flanges and remove the drums. # Remove the housing cover and gasket. # Remove the side gear pinion shaft lock bolt and the side gear pinion shaft. # Push the axle shaft inward and remove the C-locks from the inner end of the axle shafts. Temporarily replace the shaft and lock bolt to retain the differential gears in position. # Remove the axle shaft with a slide hammer. Be sure the seal is not damage by the splines on the axle shaft. # Remove the bearing and oil seal from the housing. Both the seal and bearing can be removed with a slide hammer. # Two types of bearings are used on some axles, one requiring a press fit and the other a loose fit. A loose fitting bearing does not necessary indicate excessive wear. # Inspect the axle shaft housing and axle shafts for burrs or other irregularities. Replace any work or damage parts. A light yellow color on the bearing journal of the axle shaft is normal, and does not require replacement of the axle shaft. Slight pitting and wear is also normal. # Lightly coat the wheel bearing rollers with axle lubricant. Install the bearings in the axle housing until the bearing seats firmly against the shoulder. # Wipe all lubricant from the oil seal bore, before installing the seal. # Inspect the original seals for wear. If necessary, these may be replaced with new seals, which are pre-packed with lubricant and do not require soaking. Install: # Install the oil seal. # Remove the lock bolt and pinion shaft. Carefully slide the axle shafts into place. Be careful that you do not damage the seal with the splined end of the axle shaft. Engage the splined end of the shaft with the differential side gear. # Install the axle shaft C-locks on the inner end of the axle shafts and seat the C-locks in the counterbore of the differential side gears. # Rotate the differential pinion gear until the differential pinion shaft can be installed. Install the differential pinion shaft lock bolt. Tighten to 15-22 ft. lbs. (20-30 Nm). # Install the brake drum on the axle shaft flange. # Install the wheel and tire on the brake drum and tighten the attaching nuts. # Clean the gasket surface of the rear housing and install a new cover gasket and the housing cover. Some covers do not use gasket. On these models, apply a bead of silicone sealer on the gasket surface. The beat should run specified lubricant to bring the lubricant level to ½ in. (12.7 mm) below the filler hole.
