I have the same problem for a 2002 Chevy Malibu. I can tell you the window rocker switch comes out with two clips on the window up and down ends just put a small flathead screwdriver in-between. The small panel right by the review mirrors just pops off also no screws. And there is another small panel right behind the handle the hides two screws. That
Remove the covers to your 2000 Chevy Malibu rear speakers. Remove the speaker retaining screws. Remove the wiring harness from the back of the speakers. Reverse the process to install your new rear speakers.
There is a clip on the back side of the window crank that you have to take off, then take the door panel off.
You don't need to remove front door panels, the speaker grills come out.
Remove the rear speaker cover from your 1999 Mercury Cougar speaker. Remove the rear speaker retaining screws. Remove the wiring harness from the back of the speaker. Reverse the process to install the new speaker.
If your talking about the door speakers then you will have to remove the door panels to get to the speakers.
You need to remove the panels in the trunk to get at the top of the gas tank, then you can easily remove the pump and install the new one.
You have to remove the rear seats to be able to remove the rear side panels. Then you have to disconnect the wires to the speaker, unscrew the speaker, then reinstall the new one.
Remove the belt from your 1999 Chevy Malibu alternator. Remove the wiring harness from the back of the alternator. Remove the alternator retaining bolts. Reverse the process to install the new alternator.
Remove the door speaker cover. The cover is held in place with two retaining screws. Remove the speaker retaining screws. Remove the wiring harness from the back of the speaker. Reverse the process to install the new speaker.
This depends on what type of roof panels you are trying to install. In general, you need to remove all of the nails and panels from the section that your are replacing. You then place roofing felt on the roof, making sure to nail it down. The panels go over the felt. Install them from left to right. http://www.ehow.com/how-does_4778280_installing-tin-roof-panels.html
Remove the positive battery cable from your 2000 Chevy Malibu battery. Remove the cables from the front of the starter. Remove the starter retaining bolts. Reverse the process to install your new starter.
Remove the instrument panel pad. Remove the speaker attaching screws. Remove the speaker and disconnect the electrical connector. Installation is the reverse of removal.
1.- remove the doors panels 2.- remove the old factory speakers
Remove the speaker covers from your 1997 Mercury. Remove the door speaker retaining screws. Remove the door speaker wiring harness. Reverse the process to install your new door speakers.
Remove speaker grill covers on dash to expose tweeters then remove door panels and you will se the rest of speakers
Remove the 2000 Chevrolet Malibu washer tank supply hose. Remove the windshield washer tank retaining bolts. Reverse the process to install the new windshield washer tank.
You will have to remove all trim that surrounds the speaker enclosure. Then remove the panel that houses the speaker. The speaker is removed from the rear side of this panel.
If the panels are like the 95 and 96 models, you don't need to remove door panels....carefully pop the grill covers off the door panels...there is a speaker mount behind the grill...remove the 4 speaker screws and your done. Start with the top of the grill and pull gently downward. There are metal clips on the cover and plastic hooks to the side which all hold it in place. Slow and careful is the name of the game here.
Remove the speaker covers. Remove the speaker retaining screws. Remove the wiring harness from the back of the speakers. Reverse the process to install the new speakers.
For a 2000 Chevy Silverado Ext Cab 4 dr 4x4 Z71 Front 6.5/6.75 inch speaker remove door panel and then install new speaker reattach panel. Rear 4x6 inch speaker remove rear door panel and install new speaker reattach panel.
take the door panels off, remove the housing for the Bose speakers, take apart the housing and cut the wires, put in a small speaker to replace the Bose full range speaker. (alternatively, replace the Bose housing with a custom mounting board) put the Bose housing back and the door panels back. cut the wires on the rear deck speakers and install a 6x9 speaker system. replace the CD player. (the original 2ohm Bose speakers burn out players designed for 4 or 8 ohm speaker systems)
This link will take you a nice post where you can find how to remove all panels in your Grand Cherokee. http://www.wjjeeps.com/doors/doorpanel.htm
the dash panels just pop off but you will have fun getting the switches off
You will need to remove the front speaker covers. The speaker covers are held in place with two retaining screws. Remove the speaker retaining screws. Remove the wiring harness from the back of the speakers. Reverse the process to install your new speakers.