0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Where is the ecm on a 1987 Mazda 626?
Under the dash - center console. Remove the side cover on the center console on the passenger side and you will see it on the floor board.
How do you remove the floor shifter in a 96 impala?
you will have to take the console out or at least the top piece of the console and then you will see the shifter is bolted to the floor.
Where would the computer box be on a 1988 Mazda 323?
in front of the center console on the floor mat
How do you remove the console on a 2002 buick rendezvous?
Remove the cupholder trim pieceDisconnect the electrical connectors.Remove the nuts from the side of the front floor console behind the axxess doors.Remove the nuts from the rear of the front floor console. lower rear corner may have to move seat all the way foward.Lift straight up on the front floor console and pull back in order to remove the console from the vehicle.
How do you remove the floor console in 1998 GMC Jimmy?
carefully pry up on the boot around the shifter disconnect the wires then take the box out of the console and there under the box should be the bolts to remove the complete console
How do you remove center console 99 wrangler?
Screws in the bottom hold it onto the floor.
How do you change light bulb in the gear shift of 06 Pontiac grand prix?
Front Floor Console Replacement Removal Procedure 1. Apply the park brake. 2. Remove the floor console bolts from the sides of the console. Adjust the front seats as required. 3. Shift the transaxle to 2. 4. Remove the screw from the shift handle. Remove the shift handle. 5. Pull the floor console rearward slightly. Disconnect the electrical connector at the front of the floor console. 6. Remove the floor console. 7. Remove the wiring harness. 8. Remove the HUD switch, if equipped. 9. Remove the traction control switch. 10. Remove the accessory power receptacles. 11. Remove the armrest and the hinge. Installation Procedure 1. Install the armrest and the hinge. 2. Install the accessory power receptacles. 3. Install the traction control switch. 4. Install the HUD switch, if equipped. 5. Install the wiring harness. 6. Position the floor console to the vehicle. 7. Connect the electrical connector at the front of the floor console. Slide the floor console toward the front of the car. 8. Install the shift handle. Install the shift handle screw. 9. Shift the transaxle to P. Notice: Refer to Fastener Notice. 10. Install the floor console bolts. Adjust the front seats as required. Tighten the bolts to 10 N.m (89 lb in). 11. Release the park brake.
How do you remove the console in a 1998 jeep wrangler in order to remove the carpet?
There are screws going through the bottom into the floor, should be about 6 in the front, middle, and back of the inside of the console.
How do you remove 2003 Buick Regal floor shifter console?
how to remove trans shifter cable ball socket from shifter ball
Mazda tribute 2001 fuse box location?
There are two fuse boxes on a 2001 Mazda tribute. One is in the engine compartment just behind the battery above the drivers wheel fender. The other is on the left wall near the floor forward of the drivers door down where the drivers feet rest.
How do you remove the center console of a 2000 Hyundai Elantra?
11. Disconnect the battery cables (negative first, then postive). 2. Use a screwdriver to pry out [very gently and carefully] the gear selector trim bezel from console. 3. Remove the screws holding the console to the floor. 4. Lift the console up and over the shift lever. Disconnect antenna electrical connectors and remove the console from vehicle.
How do you replace the console speaker on a 2001 Jeep Wrangler?
Remove the screws that fasten the console to the floor, there are 2 in the rear cupholder, 1 in the front cup holder, and 2 near the shifter (where the console seperates). When all the screws are removed you can lift out the console (be careful to unplug speaker wires), turn over, and remove the speaker.
