Control Panel Front 1. Disconnect the negative battery cable. 2. Remove the overhead console retaining screws. 3. Carefully release the three clips and slide the overhead console forward. 4. Detach the panel electrical connectors. 5. Remove the panel retaining screws. 6. Remove the auxiliary climate control panel assembly from the bezel. 7. The installation is the reverse of removal. Rear 1. Slide the auxiliary climate control panel assembly forward and downward. 2. Detach the electrical connectors. 3. Remove the auxiliary climate control panel assembly from te bezel. 4. Detach the electrical connectors. 5. Remove the screws. 6. Remove the climate control panel assembly. 7. The installation is the reverse of removal.
From what i have heard there is a couple clips towards the front of the console. after they are removed you can slide the entire console back to release the hooks securing it to the ceiling.
Remove the cupholder trim pieceDisconnect the electrical connectors.Remove the nuts from the side of the front floor console behind the axxess doors.Remove the nuts from the rear of the front floor console. lower rear corner may have to move seat all the way foward.Lift straight up on the front floor console and pull back in order to remove the console from the vehicle.
Remove the center console. The module will be in front of console under dash
There are screws going through the bottom into the floor, should be about 6 in the front, middle, and back of the inside of the console.
It is under the front part of the console. Take the console out and it is just directly under the heater and A/C controls on the tunnel housing.
You use the tire tools to lower the winch. The part you turn is located in front of the console between the front seats. When the tire is low enough, you can pull it out the side to remove it from the carrier.You use the tire tools to lower the winch. The part you turn is located in front of the console between the front seats. When the tire is low enough, you can pull it out the side to remove it from the carrier.
remove the front console cover by pulling on it backwards. This is held by clips and the electronic connector at the back central portion. Be careful not to break the console cover Disconnect the wires that is connected to this console to remove it entirely. Remove the metal screws that holds the stereo pull it out and disconnect all the harnesses behind it.
Front Floor Console Replacement Removal Procedure 1. Apply the park brake. 2. Remove the floor console bolts from the sides of the console. Adjust the front seats as required. 3. Shift the transaxle to 2. 4. Remove the screw from the shift handle. Remove the shift handle. 5. Pull the floor console rearward slightly. Disconnect the electrical connector at the front of the floor console. 6. Remove the floor console. 7. Remove the wiring harness. 8. Remove the HUD switch, if equipped. 9. Remove the traction control switch. 10. Remove the accessory power receptacles. 11. Remove the armrest and the hinge. Installation Procedure 1. Install the armrest and the hinge. 2. Install the accessory power receptacles. 3. Install the traction control switch. 4. Install the HUD switch, if equipped. 5. Install the wiring harness. 6. Position the floor console to the vehicle. 7. Connect the electrical connector at the front of the floor console. Slide the floor console toward the front of the car. 8. Install the shift handle. Install the shift handle screw. 9. Shift the transaxle to P. Notice: Refer to Fastener Notice. 10. Install the floor console bolts. Adjust the front seats as required. Tighten the bolts to 10 N.m (89 lb in). 11. Release the park brake.
You need to remove the front and rear seats. Remove the console, various interior panels and the door sill plates. Pull out the carpet.
it is directly under the center console between the 2 front seats. Just remove the console and wala there it is.
Remove the screws that fasten the console to the floor, there are 2 in the rear cupholder, 1 in the front cup holder, and 2 near the shifter (where the console seperates). When all the screws are removed you can lift out the console (be careful to unplug speaker wires), turn over, and remove the speaker.
remove the two light lens be careful not to break them. then remove the two torx screws behind the lens. give a slight pull down on the front of the console to remove the two clips and you are done.