0
How do you remove the fuel gauge sender on a Renault Clio - x reg petrol?
Wiki User
∙ 11y ago
first you disconnect the battery ,lift the rear seat to locate the unit,release both pipes and electrical taggs,try twisting the round plastic cap its simular to removing a light bulb but a lot harder ,when released you can remove the unit,remember you are dealing with highly inflamable fuel be safe at all times.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Where can you get a replacement petrol gauge for a 1996 Renault traffic 2 2 petrol van?
Fuel gauge problems are usually the fault of the fuel gauge sending unit in the fuel tank, just saying.
How do you check the petrol gauge on a 1998 petrol peugeot 306?
Fill up with diesel and see if the gauge still goes up. The sender unit is under the back seat, one to the left under 6" black plastic plug is the fuel pump, the one to the right is the sender unit. Prise the plug out of the floor and unscrew the the sender unit from tank. Once out it can be moved manually while the ignition is on and see the gauge moving. The float arm is stiff and am still truying to work out why as 3 others checked were all the same. To get at the dash gauge remove the steering wheel, instrument shroud and instrument panel, not a lot to see as all printed circuits.
1993 Volvo 940 fuel gauge not working Repair method?
You should first test the fuel gauge sender unit for a fault with a multimeter. The sender connector is normally located in the left hand pullout section in the trunk or cargo area. There are different resistance values for various tank levels. A reading of infinity or intermittent infinity ohms suggests a faulty sender. If the sender is bad you will have to replace it (it is located in the fuel tank). If the sender is working check the harness connector for corrosion. If the connections are good suspect the gauge. The gauge has dry soldered joints and you will have to remove the gauge to investigate. The printed circuit connections may be loose or corroded.
What does it mean when a 1974 Nova fuel gauge is stuck in the full position?
Either the wire from the gauge to the sender is broken or the sender is bad.
Where is the fuel tank gauge situated on peugeot 405?
usually under the the drivers side rear passenger seat, lift off a large black plastic cover and underneath you shall have your fuel gauge sender unit + pump if it's a petrol.
Why my Water temperature gauge doesn't work on 95 explorer?
only 3 reasons a temp gauge wont work the temp sender is bad the gauge is bad or the wire from temp sender to gauge is broken
Where is the temperature sender located for the temperature gauge on a 1990 Chevy lumina?
1990 Chevrolet Lumina temperature sender is located on the back side of the thermostat housing. The sender has a wire that goes to the temperature gauge.
Renault mengane fuel light always on gauge not working?
fuel gauge not working
How do you replace the fuel gauge sending unit in a 2000 Bonneville?
supposedly there is a cover in the trunk that you can remove to access the top of the fuel tank to replace the fuel pump and sender
Any ideas on why the Oil Pressure Gauge on a 1994 Jeep Grand Cherokee 5.2L pegs when the ignition switch is turned on already checked the sending unit wiring and tried a different gauge?
You have a ground from the oil sender unit to the gauge. This is how you check a gauge. ground out the wire at the sender and it pegs out the gauge.
How do you change the fuel sender unit on a 1998 escort diesel?
Obviously the tank has to be removed. 4 TIMES 13MM SOCKET BOLTS..REMOVE THEM This drops the tank down. Fuel filler and breather pipe(next to each other)..remove them. Then the fuel delivery/return pipes off the sender. and fuel gauge wire off the sender. pull the tank out and the sender just screws out. Money saved on repairs can then be wasted in the pub or betting shop...;)
How can I fix a broken temp gauge on my Pontiac Montana?
It could possably be the send on the motor. You will find it located beside and a little down from the oil fillter. Remove the fillter, remove the sender[caution with the wire connector, worm it up with a hair dryer] install a new sender and connect the wire. hope that works.
