Want this question answered?
http://www.HandA-Accessories.com/element/elementcdchanger.pdf
behind the glove box open it and remove both stops on the sides, then hang it down, there is a box with a lid on it, remove it and they are in there. remember that the filter are directional, air flow is from top to bottom
behind the glove box open it and remove both stops on the sides, then hang it down, there is a box with a lid on it, remove it and they are in there. remember that the filter are directional, air flow is from top to bottom
The blower motor resistor is mounted in the heater box directly behind the dash glove box. Remove the contents of the glove box and push in on both sides of the glove box stops. The glove box door will fold down exposing the resistor. Remove the two screws holding the resistor in the heater box to remove the resistor.
To lower the glove box. There are two plastic tab stops sticking up past the top of the glove box. They hit against rubber stops when the box is opened. Fold these rubber pieces to the side (They are attached only on one side so as to act as a hinge point) The glove box can now be lowered. Remove the dampener arm on the right side of the glove box by sliding the end up and out of the key slot. The glove box should be hanging down at this point.
It's behind the lower glove box, real easy to change, open the glove box and empty it, next you have to remove the damper it's on the left side at the top just push clip off and slide the damper off the stud. Then just slide the stops on each side then remove them, let the glove box hang near the floor, the filter is in the blower motor, it has a drawer I. The front just slide it out replace the filter. And just put the glove box back in reverse of how it came out
It's real simple. Empty out you glove box first, on the right side there is a small plastic guide. remove it from the glove box. Reach into the box and squeeze in on the sides to get the stops past the stop braces. The box will fall forward. That's it. Behind the glove box you will find the Cabin air filter. Now is a good time to replace it.
This is how you do it on a 2004 Camry. I expect that your Corola will be the same. Lower the glove box door. Remove the Phillips head screw on the right side of the box.Remove the snubber. Push in on each side of the housing to release the glove box stops. Once the stops clear the dahs,the glove box can be removed. Find the blower housing. The cabin air filter housing is a different color. Release the tabs and pull it out The new filter has instructions for replacing the element. WalMart now sell Fram cabin air filter elements.
Hope this helps. On a Mk2 1997 Mondeo, open the glove till it rests on stops and pull at approx 45 degrees towards you. The axle for the glovebox is set in a groove with stops which stop you accidentally removing the glovebox. If you are not sure, shine a torch by the side of the open glove box and you will see the runner and glovebox axle end.
Simple: remove the small piston on the right side of the open glove box. Squeeze in the sides of the box to bypass the stops in the back of the box. It will fall forward. While you are at it open the long door behind the box and replace the "Cabin Air Filter' while you have it open.
If it's in the same place as a DX, which I believe it is, then it is behind the glove box. All you have to do is remove the stops on the glove box, let it go all the way down, and the filter is right behind.
I own a 2003 4Runner and the cabin air filter is directly behind the "Glove Box." It's in the exact same place on my 2008 Tundra. Open and clean out your glove box. Remove the piston on the right side of the glove box, let the box drop forward. Squeeze in the sides of the glove box to bypass the stops in the back of the box. Let it drop forward. Behind the glove box you will find a long door with the air filter inside. It's that simple.