Honda Passport

How do you remove the headlamp assembly to replace the bulb on a 95 Honda Passport?

272829

Top Answer
User Avatar
Wiki User
2015-07-15 21:37:56
2015-07-15 21:37:56

To change the headlight bulb you do not need to remove the headlamp assembly. Pop the hood and behind the assembly is access to the light bulb, just unclip it and carefully pull it out from the hole. Then you can remove the old bulb and put the new one in. Don't touch the light bulb! It won't work if you do.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Open hood, remove headlamp bulb from headlamp assembly, remove (1) 10mm bolt from top of headlamp assembly, next remove (3) 10mm bolts from behind headlamp assembly, pull headlamp forward ( you may have to pry gently from the right side). Remove turn signal bulb-Done!

User Avatar

Remove the air intake splash shield from the vehicle. Remove the 2 headlamp retaining bolts. Remove the lamp assembly from the front of the vehicle. Detach the headlamp connector. Remove the headlamp bulb retaining ring. Remove the headlamp bulb from the headlamp.

User Avatar

If you are referring to the Chevy Venture, it is relatively easy. Just remove the 3 wing-nuts that hold the assembly secure, and then pull the headlamp assembly out. I have a link that shows how to do this, with actual pictures.

User Avatar

1. Open the hood. 2. Remove the front air deflector. 3. Apply light pressure to the headlamp lens to hold the headlamp assembly in place while disconnecting the retainers. 4. Lift up the headlamp assembly retainers to release. Important: Note the location and position of the headlamp adjuster retainers and the locator tab. 5. Remove the headlamp assembly, pulling straight forward from the headlamp mounting panel. 6. Disconnect the wiring harness from the headlamp assembly. 7. Rotate the headlamp bulb/socket counterclockwise to release. 8. Remove the headlamp bulb/socket from the headlamp assembly, if required. There are (2) pull up clip retainers that hold the headlamp assembly in place...Both of these must be removed for the headlamp assembly to be pulled forward...:)

User Avatar

you dont either replace assembly or if covers are fogged have them buffed

User Avatar

With the hood open remove the (2) two headlamp assembly bolts from the upper fascia support. Slide the headlamp assembly outward enough to release the headlamp bracket tabs from the slots in the upper fascia support. Position the headlamp assembly away from the vehicle body to access the electrical connector. Disconnect the electrical connector from the headlamp assembly. Remove the headlamp assembly from the vehicle. If you wish to change the halogen bulb: Disconnect the electrical connector from the headlamp bulb/socket. Remove the headlamp bulb/socket retainer ring from the headlamp, by turning counterclockwise. Remove the headlamp bulb/socket from the headlamp assembly. . G These instructions are similar from around '96 to '03 grand prix model years all trim levels.

User Avatar

Open the hood, remove the pins holding the headlamp assembly, remove headlamp assembly, now you can reach in and remove the day time bulb socket assembly to replace the bulb. Repeat procedure on other side.

User Avatar

Open the hood to the engine compartment. Remove the headlamp wiring harness. Remove the headlamp assembly retaining bolts. The headlamp will come out.

User Avatar

With the hood open remove the (2) two headlamp assembly bolts from the upper fascia support. Slide the headlamp assembly outward enough to release the headlamp bracket tabs from the slots in the upper fascia support. Position the headlamp assembly away from the vehicle body to access the electrical connector. Disconnect the electrical connector from the headlamp assembly. Remove the headlamp assembly from the vehicle. If you wish to change the halogen bulb: Disconnect the electrical connector from the headlamp bulb/socket. Remove the headlamp bulb/socket retainer ring from the headlamp, by turning counterclockwise. Remove the headlamp bulb/socket from the headlamp assembly. Hope this helps. G These instructions are similar from around '96 to '03 grand prix model years all trim levels.

User Avatar

Remove the (2) two headlamp assembly bolts from the upper fascia support. Slide the headlamp assembly outward enough to release the headlamp bracket tabs from the slots in the upper fascia support. Position the headlamp assembly away from the vehicle body to access the electrical connector. Disconnect the electrical connector from the headlamp assembly. Remove the headlamp assembly from the vehicle. If you wish to change the halogen bulb: Disconnect the electrical connector from the headlamp bulb/socket. Remove the headlamp bulb/socket retainer ring from the headlamp, by turning counterclockwise. Remove the headlamp bulb/socket from the headlamp assembly. Hope this helps. G These instructions are similar from around '96 to '03 grand prix model years.

User Avatar

With the hood open remove the (2) two headlamp assembly bolts from the upper fascia support. Slide the headlamp assembly outward enough to release the headlamp bracket tabs from the slots in the upper fascia support. (to release the tabs from the slots on the passenger side lens move the assembly to the left when facing the engine, and when doing the drivers side lens shift the assembly to the right ) Position the headlamp assembly away from the vehicle body to access the electrical connector. Disconnect the electrical connector from the headlamp assembly. Remove the headlamp assembly from the vehicle. If you wish to change the halogen bulb: Disconnect the electrical connector from the headlamp bulb/socket. Remove the headlamp bulb/socket retainer ring from the headlamp, by turning counterclockwise. Remove the headlamp bulb/socket from the headlamp assembly. Hope this helps. "G" These instructions are similar from around '96 to '03 grand prix model years all trim levels.

User Avatar

With the hood open remove the (2) two headlamp assembly bolts from the upper fascia support. Slide the headlamp assembly outward enough to release the headlamp bracket tabs from the slots in the upper fascia support. (to release the tabs from the slots on the passenger side lens move the assembly to the left when facing the engine, and when doing the drivers side lens shift the assembly to the right ) Position the headlamp assembly away from the vehicle body to access the electrical connector. Disconnect the electrical connector from the headlamp assembly. Remove the headlamp assembly from the vehicle. If you wish to change the halogen bulb: Disconnect the electrical connector from the headlamp bulb/socket. Remove the headlamp bulb/socket retainer ring from the headlamp, by turning counterclockwise. Remove the headlamp bulb/socket from the headlamp assembly. Hope this helps. "G" These instructions are similar from around '96 to '03 grand prix model years all trim levels.

User Avatar

undo the two 3/32 bolts running thru headlamp assemblies and remove headlamp assembly to access bulb

User Avatar

With the hood open remove the (2) two headlamp assembly bolts from the upper fascia support. Slide the headlamp assembly outward enough to release the headlamp bracket tabs from the slots in the upper fascia support. Position the headlamp assembly away from the vehicle body to access the electrical connector. Disconnect the electrical connector from the headlamp assembly. Remove the headlamp assembly from the vehicle. If you wish to change the halogen bulb: Disconnect the electrical connector from the headlamp bulb/socket. Remove the headlamp bulb/socket retainer ring from the headlamp, by turning counterclockwise. Remove the headlamp bulb/socket from the headlamp assembly. Hope this helps. G These instructions are similar from around '96 to '03 grand prix model years all trim levels.

User Avatar

for the removal, pull of the upper radiator sight shield, make sure that the headlamp switch and the ignition switch are turned off, raise the headlamp assembly retainers by pushing rearward and then pulling up to save time. disconnect the headlamp assembly wiring harness and remove the headlamp assembly, install just do the reverse.

User Avatar

You are going to have to replace the entire Headlamp Assembly, very expensive.

User Avatar

simply remove the two screws located on the top of the headlamp assembly and then pull the headlamp assembly forward to gain access to the light bulbs

User Avatar

Open hood. On the inside (toward the center of the car) of each headlamp is a plastic clamp fixing one side of the headlamp. On the ouside from the top unscrew the bolt holding the other side of the headlamp assembly. Lift the lamp assembly out of the car and remove (pull off)the connector to the bulb. Next peal the rubber boot from the back of the headlamp assembly. This will expose a spring clip that holds the halogin bulb in the headlamp assembly. Remove bub and replace with a new bulb being carefull to only touch the bulb by its metal base connector. Do not touch the glass areas.

User Avatar

You remove a few bolts to remove the entire headlight assembly. There is a video on YouTube on exactly this. Do a search for Forenza Replace.

User Avatar

You have to remove the entire headlamp assembly from the vehicle to access the headlamp bulb. Not too difficult, just 3 or 4 screws I think. Everything is pinned, or keyed, so you don't have to readjust the assembly after replacing the bulb & attaching the headlamp.

User Avatar

I have a 1999 Forester, but I imagine the 2003 is similar in this regard. You don't actually need to remove the headlamp to replace the bulb. On my car, I unplug the wire from the bulb at the back of the headlamp, remove the large rubber piece around the back of the bulb, unclip the clips that hold the bulb in place, remove and replace. Cheers! Mark This is a good answer and is so just as stated. Thanks Mark! RicT

User Avatar

With the hood open remove the (2) two headlamp assembly bolts from the upper fascia support. Slide the headlamp assembly outward enough to release the headlamp bracket tabs from the slots in the upper fascia support. (to release the tabs from the slots on the passenger side lens move the assembly to the left when facing the engine, and when doing the drivers side lens shift the assembly to the right ) Position the headlamp assembly away from the vehicle body to access the electrical connector. Disconnect the electrical connector from the headlamp assembly. Remove the headlamp assembly from the vehicle. If you wish to change the halogen bulb: Disconnect the electrical connector from the headlamp bulb/socket. Remove the headlamp bulb/socket retainer ring from the headlamp, by turning counterclockwise. Remove the headlamp bulb/socket from the headlamp assembly. . "G" These instructions are similar from around '96 to '03 grand prix model years all trim levels.

User Avatar

to remove the bulb simply take the four screws that attach the front assembly and it will give you access to the bulb.

User Avatar

Open the hood. There are three hex head bolts that hold each headlamp to the van. Remove each bolt and gently pull headlamp out from grill using the small handle-like grip. The headlamp will remain connected to the van with the lightbulb socket. Twist the collar away from the bulb then pull the bulb assembly out of the headlamp. Replace bulbs and reassemble components.

User Avatar

Open hood, look at headlamp assembly. There will be large white/tan cover. Turn cover clockwise to remove. Turn the headlamp assembly c-clockwise and remove.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.