answersLogoWhite

Top Answer
User Avatar
Wiki User
Answered 2008-05-04 20:32:40

This was my question and can I pull the connector straight without breaking it does it have a lock cannot see up close using mirrors and magifine glass. Need to do quick so I can replace my starter. Thanks

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Still Have Questions?

Related Questions

How do you replace a crankshaft sensor on a 1991 Buick Century?

Haynes repair manual available from www.amazon.com. Not hard. Locate sensor, unplug electrical connector, use socket of appropriate size, remove.


How do you remove a Crankshaft Position Sensor?

how to remove crankshaft position sensor from 91 Buick Regal


What does code PO141 mean for a 1998 Buick Century Custom?

02 sensor problem


Where is the crankshaft sensor on 2001 Buick Century?

its right behind the harmonic balancer....so you will have to remove the h.b them remove the crank sensor...


1997 BUick LeSabre Custom location of crankshaft sensor?

the crankshaft sensor is located behind the harmonic balancer on the ft timing cover


Where is the oxygen sensor located on a Buick rendezvous?

The oxygen sensor on a Buick Rendezvous is located immediately before the converter on the driver's side. You will need either a special socket or a wrench to remove the sensor.


How do i remove oil level sensor 1992 Buick Roadmaster?

It is not an oil level sensor it is an oil pressure sensor. It just unscrews.


Egr dpfe sensor on the 99 buick century custom?

Ford is the only American car company that uses a DPFE sensor. GM dpfe sensor are built into the EGR.


Where is the cam shaft position sensor on engine of 1994 Buick Regal 3.8L?

On a 1994 Buick Regal 3.8L engine, the camshaft position sensor (CMP sensor) is located on the timing cover, behind the water pump, near the camshaft sprocket. Basic removal and installation instructions: # Disconnect the negative battery cable. # Remove the serpentine drive belt. # Remove the power steering pump, as outlined in Section 8 of this manual. # Detach the sensor electrical connector. # Remove the CMP sensor mounting bolt, then remove the sensor from the engine. # Inspect the sensor O-ring seal and replace as required. To install: # Position the CMP sensor and secure with the retaining bolt. Tighten the bolt to 8 ft. lbs. (10 Nm). # Attach the sensor electrical connector. # Install the power steering pump, as outlined in Section 8 of this manual. # Install the serpentine drive belt. # Connect the negative battery cable.


How do you replace a oxygen sensor on a 1996 Buick le Sabre?

The 1996 Buick LeSabre oxygen sensor is located on the air cleaner housing. Remove the vacuum hose. Pull the sensor out. Reverse the process to install the new sensor.


Where is the sensor located for the electric fans to the radiator on a 95 buick regal custom?

The Sensor for the fans is located on the upper right side of the radiator, ( the Passenger side).


Where is the coolant level sensor on a 1995 buick regal?

On the passengers side of the radiator near the top and has a connector its a square shaped box.


How do you change an oxygen sensor on the odd side of a 2002 Buick Park Avenue?

on the 3.8L engine the sensor is located on the exhaust pipe just below the manifold on the firewall side. move all the crap amd hoses out of the way best you can and use a sensor socket to remove, inplug from connector amd replace with new.


Will front fenders from a 1971 Buick Skylark Custom fit a 1972 Buick Skylark?

will the fenders from a 1971 Buick Skylark Custom fit a 1972 Buick Skylark?


What does a 1996 Buick regal custom look like?

Google 1996 Buick Regal Custom and see.


How do you replace the drivers side mirror on a buick rendezvous?

In order to replace the drivers side mirror on a Buick Rendezvous, you will need to remove the door panel. You will have to disconnect the electrical connector and you will be able to remove the mirror and place the new one on.


Where is throttle sensor on 91 buick regal?

It is mounted on the throttle shaft usually on the other side from the throttle cables. It has a three wire connector plugged into it.


Coolant level sensor location on a 1995 buick skylark custom?

Not positive, but there is something attached to the bottom of the coolant tank, maybe that's it.


Where is the vehicle speed sensor located on a 1990 buick century?

The sensor is locatedon the top back of the transmission. You have to remove the air filter, and housing to easily get at at.


Cam sensor problems 3800 buick lesabre 92?

It should be in the front of the engine as part of the front cover, it will have a 3 wire connector. Understand that if you remove, replace this part you will have to re-align it to the proper timing mark on the crankshaft dampner. TommyTrouble


Where is drain plug for the radiator of a 1992 Buick Regal Custom?

where is the drain plug for the radiator on a 1992 buick regal custom


Where is the transmission solenoid located on a 1995 Buick skylark custom?

Where is the transmission solenoid located on a 1995 buick skylark custom?


Where do you find starter relay for 99 Buick lesabre custom?

Where do you find starter relay for 99 buick lesabre custom


Where is the coolant temperature sensor on 2005 Buick rendezvous?

The coolant temp sensor is located at the thermostat housing... can see it between the driver side front engine mount and the throttle body. It is a 2-wire connector


What the difference between 1992 Buick LeSabre Custom and Buick LeSabre Limited?

Custom is lower end. Limited has more features.


Still have questions?