Grand Prix GT

How do you remove the rear speaker cover on a 2000 Pontiac Grand Prix?

232425

Top Answer
User Avatar
Wiki User
2011-11-25 16:39:53
2011-11-25 16:39:53

You need to remove the rear seat to access the speakers and remove the covers.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

The 1999 Pontiac Grand Am speakers can be removed by removing the speaker cover. The speaker cover is held in place with two screws. Remove the speaker retaining screws. Remove the wiring harness from the back of the speaker.

User Avatar

The 1997 Pontiac Grand Prix rear deck speaker covers are held in place by four retaining screws. Remove the retaining screws to remove the covers.

User Avatar

What do you mean by headlight cover?What are you trying to do?JW

User Avatar

You have to remove the entire dash panel that the speaker grills are located on. Just pry the entire cover off from either the drivers side or passenger side. Shouldn't take too much work. I have the same car and replaced my speakers also. The speaker grills do not come off of the dash cover.

User Avatar

Begin by removing the cover from your rear speakers. Remove the rear speaker retaining screws. Remove the wiring harness from the back of the speaker. The rear speakers will come out.

User Avatar

remove the spark plug cover. and the valve cover to reach it its right under the cam pulley

User Avatar

open trunk remove carpet over taillight remove retaning screws

User Avatar

The 1995 Pontiac Grand Am 3.1 liter engine crank shaft sensor is located inside of the rear engine cover. You will need to remove the rear engine cover in order to access the crankshaft sensor.

User Avatar

Follow the upper rad hose to the engine. You will need to remove the engine cover. To remove the cover turn the oil filler neck (not the cap).

User Avatar

from shop manual: remove luggage cover and holder assembly remove speaker cover retainer nut and and screws securing the cover in place over the speaker assembly loosen and remove the speaker retainer screws securing the speaker in place, lift the speaker out enough to access the wire harness at the rear of the assembly disconnect the speaker harness remove the speaker installation is the reverse of removal

User Avatar

where is valve cover located on a 2001 Pontiac Grand-Am 4 cyl

User Avatar

To replace a Pontiac Grand Am bumper cover, start by taking out either the three bolts on the side of the fender or in front of the wheels. Remove the top pushpins to remove the cover. Push back the two pins for each headlight, and pull them up. Unplug the lights. Then, get the replacement bumper, and snap it into place like the previous one.

User Avatar

You do not need to remove the door panel to change your speakers. Remove the speaker cover, by prying outward on the speaker cover retaining clips. Remove the speaker retaining screws. Remove the wiring harness from the back of the speaker.

User Avatar

I did this with my 1996 Lumina APV. If you have rear speakers, remove the speaker cover(s), remove the speaker and reach in and find the mechanism, turn it to open. May have to do simultaneously for both sides. Then remove the tailgate panel and repair.

User Avatar

on top of the engine there is a cover sheild. remove the cover by the four bolt. the plug boots will come with it, the spark plugs are down in the holes.

User Avatar

Remove the door speaker cover. The cover is held in place with two retaining screws. Remove the speaker retaining screws. Remove the wiring harness from the back of the speaker. Reverse the process to install the new speaker.

User Avatar

If your key is stuck: on the underside of the steering column cover there is a round recess cover. Remove the cover and using a pecil push up through the recess.

User Avatar

Remove the rear speaker cover from your 1999 Mercury Cougar speaker. Remove the rear speaker retaining screws. Remove the wiring harness from the back of the speaker. Reverse the process to install the new speaker.

User Avatar

On the bottom of the dash on the passenger side remove the black cover then remove the bolts on the blower and disconnect the wire. Reverse above to install.

User Avatar

If it is anything like the '96 Grand Am, it is located under a cover between the engine and firewall. The cover has 3 bolts in it. Remove the bolts and the cover and you will find the O2 sensor (front - the other is just after the catalytic converter.) You will need a 7/8" wrench to remove the part.

User Avatar

The 1990 Chevy Corvette front drivers side speaker cover will need to be removed. Remove the speaker retaining screws. Remove the wiring harness from the back of the speaker.

User Avatar

Follow the large hose on the top right of the radiator back under the plastic engine cover. Thermostat is inside the metal cover at the end of the hose. Remove cover with 10mm socket.

User Avatar

you need to remove the door skins first there is a screw on the inside of the speaker cover that holds it on.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.