Dodge Intrepid
Toyota Camry
Ford F-150

How do you remove the starter on a 1993 Dodge Intrepid?

323334

Top Answer
User Avatar
Wiki User
2011-09-12 20:35:20
2011-09-12 20:35:20

If the same as my 94 Intrepid with the 3.3, it should be held on by 3 bolts, jack up drivers side of car, disconnect battery, unbolt, the starter shouldn't fall out, but make sure it comes out slow, and you disconnect the positive connection as well as the clip on piece that goes to the solenoid. Easy as pie.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Dodge Intrepid was created in 1993.

User Avatar

where is the crankshaft sensor located on a 1993 dodge intrepid

User Avatar

It is towards the bottom of the motor on driver's side. three bolts on the starter on and also a clip/connect. It is best to raise/jack the car on driver's side to remove from bottom.

User Avatar

O,YEA AND I FORGOT TO MENTION IT IS A 1993 DODGE INTREPID...

User Avatar

The positive goes on the large stud. The engine ground wire goes under the center starter bolt.

User Avatar

Dodge does not use inertia/reset switches.

User Avatar

The 1993 Dodge Intrepid had two OEM tire sizes. The factory fitments for this vehicle were the P205/70/15 and P225/60/16 sizes.

User Avatar

The curb weight of the Dodge Intrepid in 3,318 pounds of 1,505 kilograms. It was produced for model years 1993 until 1997.

User Avatar

It is inside the fuel tank. 1993-1997 there is an access in the trunk. 1998-2004 you have to remove the tank to access.

User Avatar

When changing out the spark plugs of a car, maintaining the gap is important to help the car run correctly. For a 1993 Dodge Intrepid the spark plug gap is 0.04 millimeters.

User Avatar

Remove the tilt steering lever.Remove the steering column cover.Unplug the wire going to the switch.Now you can remove the bolts that hold the switch to the column.An instructional video of how to remove the multifunction switch on a 1993-1997 Dodge Intrepid has been included below.

User Avatar

Remove the positive cable from your 1993 Mercury battery. Remove the cables from the front of the starter. Remove the starter retaining bolts. Reverse the process to install your new starter.

User Avatar

on the starter its self>>>>JAC

User Avatar

The 3.5 SOHC engine found in a 1993 Dodge Intrepid puts out 214hp and 221ft/lb of torque to the crankshaft.

User Avatar

No, you will have to remove the tank.The 1993-1997 Intrepids where the only ones with access panels.No, you will have to remove the tank.The 1993-1997 Intrepids where the only ones with access panels.

User Avatar

93 dodge caravan starter changedisconnect battery, then underneath at the front mount disconnect wires if possible, if not, remove after removing starter. three bolts and starter comes out. one bolt is slightly hidden. opposite to install.

User Avatar

The dodge intrepid didn't come out until 1995. the type of automatic transmission in it is the A606 also known as a 42LE transaxle.

User Avatar

A 1993 Intrepid does not have a distributor cap.A 1993 Intrepid does not have a distributor cap.

User Avatar

Remove the positive battery cable from your 1993 Chevy Cheyenne battery. Remove the two cables from the front of the starter. Remove the three starter retaining bolts. Reverse the process to install the new starter.

User Avatar

Answeryou can go to www.carcreditkansas.comunder the steering column

User Avatar

The engine computer is also the voltage regulator.

User Avatar

Do you mean EFI (Electronic Fuel Injection)? If so, the answer is yes.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.