answersLogoWhite

0


Best Answer
Copy

You can get a Window handle remover from an automotive parts store that'll help remove a clip that holds on the handle. With this you can remove the clip and then the handle.

User Avatar

Wiki User

โˆ™ 2007-07-13 12:29:24
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you remove the window crank from a 1998 Pontiac Gran Am?
Write your answer...
Submit

Related Questions

How do you remove the window crank on a 1998 dodge neon?

Pull out the U-clip located on the base of the window crank.


How do you remove the window handle from a 1998 Pontiac Sunfire?

Don't know, would like to know.


How do you fix a stuck driver side electric window on 1998 Pontiac firebird on a 1998 Pontiac firebird?

How do yo fix a stuck driver side electric window on a 1998 pontiac firebird.


How do you remove a manual window crank on a 1998 Pontiac Sunfire?

The question you ask is too involved for a proper answer. You may want to go to a car parts store, or book store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.


Is a 1999 Pontiac grand am power window switch compatible with a 1998 Pontiac grand am power window switch?

If it looks the same it will probably work.


Where do you find the Crank sensor A for 1998 Pontiac Transport?

Its located under rear manifold remove coils and bracket reach just behind manifold 10mm socket needed


How do you remove the evaporator core of a 1998 Pontiac Bonneville?

Before you remove the evaporator core from a 1998 Pontiac Bonneville you need to have the air pressure discharged. You will then need to remove the AC unit. You will need to remove some screws before you can remove the evaporator.


What causes intermittent power window failure in a 1998 Pontiac Grand Prix?

There are a couple of different reasons as to why there would be power window failure in a 1998 Pontiac Grand Prix. One reason could be a faulty fuse or it could also be a short in the window motor.


How do you remove the window crank on a 1998 Plymouth breeze?

It is held in place by a horseshoe shaped clip. the clip is removed by reaching behind the handle with a small pick and pulling the clip out.


How do you remove passenger side window crank handle on a 1998 hyandai elantra?

There is a clip holding the handle. It is located in the center in the back of the handle. There is a tool to remove & install it; but you can use a flat screwdriver carefully. Good luck.


How do you remove a window crank on a 1998 Chevy S10 pickup?

There is a "C" clip behind the handle that must be removed. Your local auto parts store can sell you an inexpensive tool to help you remove the clip without damage done.


How much horsepower does a stock 1998 Pontiac grand prix gtp have?

Crank- 240hp WHP- Roughly 200hp


How do you remove the door panel from a 1998 Elantra?

1. On manual window models remove the window crank handle dislodge the clip 2. Remove the outside mirror cover 3. Detach the door handle trim piece and disconnect the door pull mounting screw. Unplug the electrical connector from the power window switch 4. Remove the retaining screws and detach the panel by carefully prying it away from the door


How do you install a driver side window on a 1998 Pontiac Firebird?

u have to remove the drivers window and remove the regulator assy...once its out there ar 4 rivits u have to drill out be very carefull of th spring in the regulator it will come out and injure u if u don't take the proper precautions


Replacing a back window on a Monte Carlo?

How do I remove the back window in a 1998 Monte Carlo? how do I replace this?How do I remove from other Car's model


How do you remove 3rd brake light ON A 1998 PONTIAC GEAND PRIX?

with a hammer


How do you remove a manual window crank from the door panel in the door of a 1998 Chevy s10?

Your local auto parts store will sell you an inexpensive tool to do that job. There is a spring clip that has to be removed from behind the handle.


Remove window crank handle from 1998 Chevrolet 1500?

If it doesn't have a screw in the center--if may be secured by a horse shoe type clip behind handle--tool available at auto parts store


Why does the window on a 1998 Pontiac transport go down on an angle?

the frame that holds the window in is bent and you have to change the whole inside of the door not just the frame.


How do you remove the crank shaft vibration dampener on a 1998 Chrysler Sebring convertible?

After removing the right front tire and fender liner, you remove the serpentine belt. You then remove the crank bolt and use a puller to remove the pulley.After removing the right front tire and fender liner, you remove the serpentine belt. You then remove the crank bolt and use a puller to remove the pulley.


How do I remove a cassette tape stuck in the player in my Pontiac Grand Am?

How do I remove cassette tape stuck in my 1998 Volkswagon beetle


The rear window on the 1998 Lincoln Continental is stuck down how to fix it?

Remove the inside door panel. You will be able to see the entire window mechanism. Remove the obstruction that is keeping the window from closing.


Where is the crank shaft sensor located on a 1998 Pontiac Grand Prix?

It's on the inside of the Harmonic Balancer Pully. It shoud be blue in color


Where do one remove the evaporator core on a 1998 Pontiac bonnevile?

To remove the evaporator core on a 1998 Pontiac Bonneville, you will need to remove the dashboard. An alternative method is to access the core underneath the hood. The core can be found at the passenger side near the strut tower. Once the area is accessed, you will need to remove some of the firewall to properly remove the core.


How do you remove a window crank from a 1998 Tacoma?

it's not easy unless you have done it before.if you look closely there is an clip that holds the the crank handle on a spline.there is a recessed part of the crank handle,by using a small screwdriver you can pry the clip toward you,use caution and safety glasses,with a few trys you will grasp the technique needed to remove it.note:you may need a flashlight to see the end of the clip.a pocket screwdriver worked the best for me.