0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you repair rear door latch on a ford e350 van?
How to repair the rear door latches on my e 350 van. The bottom latch will not hold . How do I get the latch to hold Thanks
How do you repair Chevy Express 2000 rear van door latch?
left door latch is broke
Is there a secret latch on 1997 Honda Passport to open the rear door?
The 1997 Honda Passport does not have a secret latch to open the rear door. The rear door latch can be found just above the license plate holder.
How do you replace the rear dutch door latch on a 1997 gmc safari?
= How do you replace the rear dutch door latch on a 1997 gmc safari?" =
Repair 2002 Sequoia rear door latch?
You need to removed the plastic cover on the inside and manually un-lock the latch. There is no easy way. The dealer want $270 to $290 if they do it.
Where is the rear door jamb sensor at on 99 jeep Cherokee?
It is part of the latch inside the door.
How do you fix ford e150 rear door latch?
1A Auto
How to repair broken outside rear door latch on 1992 astro van?
to get to the latch rod you will need to pull the plastic trim fasteners from the door and take the screws out of it on the bottom of the door. Pull the trim out just far enought to go thuought the top access hole after you cut a hole in the plastic vapor barrier and the latch rod will be just a few inches to the right pull up and the door will open.
How do you repair the rear latch on the 2006 Suzuki Grand Vitara keyless entry?
To repair the rear latch on the 2006 Suzuki gran Vitara keyless entry you need to first remove the latch from its position. Next, spray the latch with WD40 to loosen it and either replace it or hit it softly with a hammer until it starts to work.
How do you repair the drivers side rear sliding Door that won't open on a 1996 Chrysler Town and Country Lxi van?
Remove the inner door panel & you should be able to manually work the inner rods that control the operations of the latch assembly. If that doesn't work, I have had to actually do the above, & physically kick the rear section relatively hard to free up a lower rear latch mechanism that sometimes becomes rusted & will not allow the door to open.
How do you locate the door ajar sensor on the rear driver side latch on a 1999 Chrysler LHS?
It is inside the latch itself.
How do you remove the outer door handle on a ford freestyle?
Removal of Rear Door Latch is necessary first. Rear Door Latch Removal: All vehicles 1. Remove the rear door interior trim panel. 2. Remove the access hole watershield. 3. Reconnect the window regulator and window switch electrical connectors and position the front door window to access the glass clamp bolt. 4. Disconnect the window regulator and window switch electrical connectors. 5. Loosen the window glass clamp bolt. 6. Tape the window in the full up position, then lower the window regulator downward until it reaches the stops at the bottom of the regulator track. 7. Remove the interior door handle bolt. 8. Disconnect the rear door latch assembly electrical connector. 9. Rotate the push button rod downward and remove it from the rear door latch assembly. 10. Remove the 3 rear door latch assembly-to-rear door module bolts. 11. NOTE: Make sure that the interior door handle does not get scratched when it is passed through the rear door module. Remove the 8 bolts and position the rear door module aside. FIVE HUNDRED AND MONTEGO 12. Remove the tape and lower the window glass. 13. Remove the scrivet. 14. Remove the rear door glass run top bolt. 15. Remove the rear door glass run seal. 16. Carefully position the glass aside, then remove the rear door glass top run. ALL VEHICLES 17. Disconnect the exterior door handle actuating rod from the rear door latch. 18. Remove the 3 rear door latch bolts. 19. Remove the rear door latch assembly. 20. Remove the remote cable cover from the latch. 21. Disconnect the interior door handle actuating cable from the rear door latch. 22. Remove the rear door latch from the bracket. * If necessary, remove the door lock actuator and the door ajar switch. INSTALLATION ALL VEHICLES Note: If necessary, install the door ajar switch and the door lock actuator. 1. Install the rear door latch on the bracket. 2. Connect the interior door handle actuating cable to the rear door latch. 3. Install the remote cable cover on the latch. 4. Position the rear door latch assembly. 5. Install the 3 rear door latch bolts. * Tighten to 12Nm (9 lb-ft). 6. CAUTION: The exterior door handle and the door latch must be installed and tightened to specification before connecting the exterior door handle actuating rod with the yellow clip. CAUTION: The exterior door handle actuating rod must be hanging freely then clipped into the door latch. Loading the exterior door handle actuating rod up or down when connecting may result in a misadjustment of the latch causing the latch not to operate correctly. Connect the exterior door handle actuating rod to the rear door latch and close the yellow clip. FIVE HUNDRED AND MONTEGO 7. Install the rear door glass top run and carefully position the glass. 8. Install the rear door glass run seal. 9. Install the rear door glass run top bolt. 10. Install the scrivet. 11. Raise the window glass and tape it in the full up position. ALL VEHICLES 12. NOTE: Make sure that the interior door handle does not get scratched when it is passed through the rear door module. Position the rear door module and install the 8 bolts. * Tighten to 8 Nm (71 lb-in). 13. Install the 3 rear door latch assembly-to-rear door module bolts. * Tighten to 12 Nm (9lb-ft). 14. Install push button rod on the rear door latch assembly. 15. Connect the rear door latch assembly electrical connector. 16. Position the interior door handle and loosely install the bolt. 17. Untape the window glass, then lower the window glass. 18. Install the window glass clamp bolt, * Position the window in the window clamp. * Shift the door window glass fully forward. * Tighten to 8 Nm (71 lb-in). 19. Install the access hole watershield. 20. Install the rear door trim panel. 21. Center the inside door handle alignment pins to the rear door trim panel and install the interior door handle bolt. * Tighten to 7 Nm (62 lb-in). EXTERIOR REAR DOOR HANDLE REMOVAL: Remove: 1. Remove the rear door latch. 2. CAUTION: Hold the bezel cap when removing the bolt or damage to the door may occur. Using a T-5 torx socket installed on the bolt tip, loosen the bezel cap bolt until the bezel cap can be removed. 3. Shift the exterior door handle rearward and remove the exterior door handle. 4. Remove the exterior door handle gasket. 5. Loosen the exterior door handle reinforcement bolt. 6. Remove the exterior door handle reinforcement from inside the door. 7. Release the bezel cap from the bezel and remove the bezel cap bolt. INSTALLATION 1. Install the exterior door handle reinforcement on inside the door. 2. Tighten the exterior door handle reinforcement bolt. * Tighten to 7 Nm (62 lb-in). 3. Install the exterior door handle gasket. 4. Install the exterior door handle. 5. Install the bezel and the bezel cap bolt. * Tighten to 12 Nm (9 lb-ft). 6. Position the exterior door handle forward. 7. Snap the bezel cap on to the bezel. 8. Install the rear door latch.
