0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Can the clutch on a Sept 2000 polo be adjusted?
No ,There is a auto adjuster.
How do you replace the brake shoes on a 1995 polo 1.4?
How do I replace rear brakes on a VW Polo GTI
How long to do VW Polo clutch?
Hi There, it depends how you use your clutch, Most people damage their clutch because of incorrect use of clutch. Always make sure when you apply brakes you press the bake pedal only, therefore be fore the rev counter reaches 10 then you can press your clutch pedal. That will assist your engine to slow smoothly, just imagine pressing half clutch and hald break, the friction between your clutch plate and engine increases because the engine speed is still high, Just imagine doing that while you are doing 120Km/h,
How do you change a vw polo clutch cable?
Changing a VW Polo clutch cable requires exposing both ends of the cable. An open ended wrench will be needed to loosed the existing cable. After replacing the cable, be sure to bleed the line to prevent failure.
Whats the air pressure on a VW Polo?
28
Why does my Volkswagen polo not inject fuel even though the pressure is okay to injector?
your injectors are blocked replace or clean id clean because it cost's £167 each for the injectors new
Fix clutch vw polo fox?
If by fixing the clutch you mean replacing it ? Replacing the clutch is relatively straightforward: Parts needed: Throwout bearing Transmission clutch kit including pressure plate and driven plate rear main seal for the engine rear transmission mount rubber. Shifter linkage rebuild kit ($20 bux from the parts place, google on web) 3 qts redline MTL transmission oil 17 mm hex wrench to drain and replace fluid (think Sears here) Borrow of buy a clutch alignment tool (no not the rabbit style) With vehicle on ground loosen the front wheel hub nuts (they are on VERY tight >150Lbs/ft torque) Remove the battery ground connection after noting any radio securoty codes you may have. Chock the wheels , jack up the front of the vehicle, secure on jackstands. remove the drive shafts on both sides baggie the CVs so you don't contaminate them. Mark and emove the starter wires, remove the starter. If starter is old consider getting it rebuilt at this time. remove the shifter linkages, replace all the worn plastic bits, bag and lay aside. Support the engine with a floor jack. Loosen the front engine snubber mount (near the crankshaft pullry) remove the transmsiion mount (looks like a sqaushed starred donut) under drivers feet (approximately) Remove the mount bracket I suggest you renew the mount at this time Remove the clutch cable from the clutch lever remove the bolts holding the tranny to the engine Lower the engine at the rear SUPPORT the transmission and slide the unit off the pilot bushing. PUT NO PRESSURE on the transmission input shaft!!! Lower tranny to ground and remove from under unit. mark the pressure plate (clutch cover) as to orientation with a witness mark. Remove it and the clutch driven plate, don't breathe the dust. (BAD for humans) Note the driven plates spline orientation. Clean the pilot bushing in the center with carb cleaner, regrease when dry with a smear of MOS2 greas (black and ugly type) Not too much just a thin smear. Clean the transmission shaft with WD40 or Kerosene, dry with clean rag. Remove and replace the throwout bearing, if you've been breaking clutch cables lately the pivot point on the side of the case where the thowout shaft lives is dirty. It needs to be cleaned w/cleaner and lubed with MOS2 grease. Place the clutch plate in position, make sure you get the splines oriented correctly. Clean the steel surface of the clutch pressure plate with a light hydrocarbon like lighter fluid, no grease here... I've used starting fluid here in a pinch, no smoking ;-) Place the clutch cover (new unit? orient the same as the old one) over the plate. Use the tool to center the plate under the cover. If you mis-align the plate putting the unit back together will be a painful experience... so be careful, check your work. Tighten the plate into position, use a cross pattern on the bolts. Don't be sloppy here , a bolt coming loose would be bad $$$$$... Add a small amount of grease onto the transmission input splines. This helps the clutch action, not a lot just a bit to make the shaft shiny. If you're strong enough you can lift the transmission into position and slide it onto the plate splines. Otherwise use a floor jack to lift into position. Put the tranny in gear so that you can spin the axel adapter to move the shaft splines to get them to align. Reverse this procedure to finish up. I recommend driving the car after initially adjusting the pedal for 12mm or 1/2 free play. Drive the car and re-adjust as needed. Get the transmission hot by driving for an hour. Drain the fluid. replace the bottom plug after it stops dripping Add fluid to the side plug till the fluid runs out. replace the plug. Enjoy the new clutch.
How much to replace a windscreen for a v.w. polo 1998?
200
How do you change a rear license plate light bulb on a VW polo 1999?
see:How_Change_VW_Polo_1999_Number_plate_light
How to Replace Volkswagen polo brake light bulbs?
To replace the brake light bulbs on a VW Polo, pull away the carpeting in the trunk, unscrew the bolt holding the lights on, and disconnect the wiring. Replace the bulbs, put the wiring and bolts back, then replace the carpeting.
What Price is a new clutch and master cylinder for VW Polo?
straight from the dealer u are looking at plus/minus R15000
Replace brake light switch on vw polo?
You will want to replace a brake light switch on a VW Polo professionally. You do not want to make a bigger situation than you already have. A mechanic will do the job correctly.
