answersLogoWhite

0


Best Answer

No special tools required. Obtain a new fuel filter before starting, making sure it is specifically designed for your engine. Fuel injection system filters are built to withstand high pressure where filters made for carbureted systems may burst from the high pressure. The fuel filter is mounted within the left frame rail. Position the front end of vehicle higher than the rear to prevent siphoning. Remove the fuel cap and reinstall it after relieving the fuel system pressure. Clean the fittings before continuing. Disconnect the push-connect fittings from the filter. Note which way the arrow on the filter is pointing - the new filter must be installed the same way. Loosen the clamp screw and detach the filter from the bracket. Install the new filter in the bracket with the arrow pointing in the right direction and tighten the clamp screw securely. Carefully connect each fuel line to filter. Start engine and check for fuel leaks. - From Haynes Repair Manual for Ford Ranger Pickups 1993 - 2005. Good luck.

You will need special tool to remove the fuel filter do to no tools small enough to get on the 5/16 lines . The spacing on the small line is a 1/4 inch on 1 side and 3/8 of an inch on other side the only accessible line is the 3/8 's line. So take to a garage and have it done

User Avatar

Wiki User

โˆ™ 2010-10-19 17:28:17
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How do you replace a fuel filter on a 2003 3 liter Ford Ranger any special tools needed?
Write your answer...
Submit
Related questions

What special tool is needed to replace the fuel filter on a 2004 Chevrolet Impala?

no


What special tool needed to change fuel filter 2000 camaro?

You don't need any. You should be able to replace its fuel filter with a screw driver and pair of pliers.


What should you do if there is oil in your air filter?

Oil in an air filter is commonly caused by a bad PCV filter. Check the filter, and replace as needed.


How many quarts of oil are needed after new filter for a 1987 Ford Mustang 4 cylinder?

4 Liters when you replace the filter. Always replace filter when you change the oil.


How do you change a fuel filter on a 2003 Tahoe?

is a special tool needed


Tools needed to replace fuel pump on a 1996 Plymouth breeze?

no special tools are needed


How do you do a tune up on a 1998 Ford Contour?

Replace the plugs: change the oil and filter. Check the air filter and replace if needed. Replace the fuel filter if it is more than 25,000 miles or 5 years old. That's about it!


What tool needed to replace filter?

it depends on which filter you have. sometimes you need only a screwdriver but sometimes you need line wrenches


What air filter will replace generac od9723?

Many types will be able to suffice in the situation. Take the filter in with you for comparisons and ask for help if needed.


What degree of mechanical ability is needed to replace a timing chain on a 2002 Ford Ranger?

Above average. Not a job for a novice.


Where is the oil filter located on a 2003 dodge Dakota?

The oil filter on a 2003 Dodge Dakota is located on the bottom, right side of the engine. A special filter wrench is needed to properly grip and remove the filter.


Can you buy a filter without purchasing the whole pump?

Depends on what vehicle it is installed on. If the filter is mounted in the tank then you would not replace the filter unless the pump needed replacing also. If the filter is outside the tank it can be purchased separately.


How many kilometers needed before changing fuel filter in Isuzu cosswind?

Replace your fuel filter every 50,000 miles or as recommended in your owners manual.


Where is the fuel filter located on 1998 corvette?

The filter is located on drivers side back gas tank area up above the exhaust pipe. Follow the fuel line from the tank to the filter. Special tool is needed to replace it, just go to a Chevy dealer and let them install it for only $42.00[[User:65.89.157.4|65.89.157.4]]I just had it done.


Are special tools needed to rebuild a ranger 4r44e transmission?

Yes they are you need a few tools not to hard to get they will cost about 100-300$


Could an in-line filter cause the water flow to drop?

Yes, replace filters as needed. Brand new in-line filter still can cause flow restriction.


How do you replace the overdrive solenoid for a dodge ram truck?

Take down the transmission oil pan, remove the transmission filter if needed. Replace solenoid. Replace all and refill transmission


What indications does a car do when the fuel filter needs to be changed?

Hard to start, stalling, poor performance. Replace it an you will then know if it was needed.


Do you need a special tool to get off fuel lines from filter on 89 Chevrolet celebrity?

No, special tools are not needed to change a fuel filter on a 1987 - 1990 Chevy Celebrity. The proper size of open end wrenches work fine.


When should the timing belt on your 1999 Ford Ranger be changed?

Inspect at 120,000 miles , replace if needed ( Ford maintenance and the Gates website ) for the 2.5 liter , 4 cylinder , in a 1999 Ford Ranger


No, there is no special driver needed?

No, there is no special driver needed


How do you replace the fuel filter located on a 1999 Toyota Sienna?

It's under the air filter assembly. Remove the air filter compartment and the fuel filter will be underneath. It's bolted to the sidewall with a bracket. Remove the in and out fuel lines to the filter, then unbolt from the sidewall. Reverse the process with the new filter then replace the air filter compartment. Basic tools are only needed (i.e., sockets, adjustable wrench, screwdriver, etc.) I did mine and it took about an hour, was not that difficult.


What tools are needed to replace the alternator on a 1991 prelude?

Common hand tools, sockets and wrenches. Nothing special.


What parts are needed for a 4.3l chev tune up?

You didn't mention what year but in most cases you will want to replace the spark plugs, air filter and fuel filter for a minor tune up. For a major tune up you would replace the spark plugs, spark plug wires, distributor cap, distributor rotor, PCV valve, air filter and fuel filter.


How do you replace a camshaft position sensor on a 90 Oldsmobile 98?

It is pretty technical and special tools are needed. Take it to a garage.