Remove 1 retaining bolt and pry out gently on entire headlight assembly. This will let you access your bulbs. Once you've removed the retaining bolt, you probably can't pry out the headlight assembly with your hands. There are two "retaining clips" for lack of the proper description that hold the assembly firmly in place. You need to "pop" these clips free. One clip is on the far outside edge of the lamp, and the other is closer to the engine, about 3/4's of the length of the assembly in from the outer edge. You can use a screwdriver to gently pry the headlight assembly out. User note: I wrestled with the process above for about two hours, removing the one bolt and trying to remove the headlight assembly by wiggling it by hand. I couldn't get it out. I thought for sure that there must be another bolt or screw holding the assembly in, but I couldn't find it. So, after much hesitation, I took the description on faith and used a screwdriver to create some leverage. The assembly popped right out and I was able to easily change the bulb.
How do i replace the headlight switch on a 03 trailblazer in detail. Such as what needs to be removed befor the switch is installed and with what tools .
With tools and alot of patience
To replace the brake pads on a 96 Grand Am, three tools will be needed. First, a C-Clamp, then a hex key to remove the caliper bolts, and a screwdriver to work the caliper free.
What size motor? What accessories do you have? BClear.
With two special tools, a slim 36mm wrench and a spanner to hold the pulley.
A 10mm wrench, a flat blade screwdriver and a jack.
I had the same problem.Follow one of the hoses off the alternater.The hose that goes next to the antifreeze resevior is where the sensor is. This is called a low pressure switch for the a/c unit. Tools involved adustable wrench and $30.00
power tools and machine guns
Replacing a headlight bulb on a Honda Passport is very easy to do. The hood will need to be opened to change the bulb. The old bulb can be pulled off by using the connector and the new one put in. No tools are required.
The tools required to replace a front brake pad and rotors on a 2000 Jeep Grand are lug wrenches, a jack, jack stands, and a C-clamp. You also will need a wrench and a turkey baster for drawing out old brake fluid.
Yes, the Cherokee people did (and still do) use tools and weapons. They were farmers, hunters, had a written language- and some of the Cherokee people served as a unit of mounted soldiers for the Confederate Army.
because they were gay
The Cherokee tribe used several different types of tools. They used arrowheads, stone and bone shovels, fishing poles, and spears.
No tools required. At the top of the headlamp assembly there are two L-shaped pins that are snapped into a plastric groove. Rotate the pins out of the snaps and pull the pins straight up. The entire headlight assembly will now slide forward to replace any bulb. Details are also in the owner's manual.
My husband and I own a body shop. People always think they can fix a window regulator but it is not as easy as you think. I have been working in our shop for aprox. 25 years and I still hate working on doors. My suggestion, get a professional. They have tools that make taking the panel off, regulator out and also tools to put the regulator in, a whole lot easier. Sorry.
whats tools do i need to replace my rear struts on my 95 camaro
In order to replace the headlight bulb on a 99-01 ga gt the ram air cover needs to be removed. After doing that, locate two metal "L" shaped clips from the adjusting brackets. No tools are really necessary, however it is easier if you use some needle-nose pliers. Also, when replacing the bulb be careful not to drop the metal piece inside the headlights, man that thing is HARD to put back in! Good luck cause GM pulled a real job on these!
there is a little round circle to unscrew on the back, take it off but rememeber which way you take it off as there is a wrong way and right way to put it back on (know from expereince) and then replace the bulb. Hope this helpsAnswerIf it's the same as a 1996, you unscrew the top screw for the headlight & then you can unscrew the bottom screw, but I ended up breaking off the brackets because the 2nd screw is located between the headlight & the blinker housing, where there's absolutely no room to put any tools. I had no way to get that 2nd screw off, so you may be lucky to fit your hand in through the top & just untwist the bracket, but it's just easier to take off the housing. I guess a friend got his off by using an Allen wrench? The headlight does stay in there just fine even with the brackets broken off on the bottom, just make sure you get the top screw nice & tight. I've had no problems after that.
To replace the parking light located next to the main beam, you do not need any tools. The socket twists and pulls out of the lens housing. An instructional video has been provided below that will show you exactly how to do this. Hope this helps, 1ATony
With my snap on tools......... remove the bolts holding the water pump on and the old water pump will fall off. If you have to ask how to remove a water pump from this vehicle, you will be better off having replaved by a professional mechanic as this job is soooooo easy.
what tools do i use to change the front brakes in my 2003 Pontiac grand prix
There are adjusting points on the corners of the headlight housing, this should be done by a professional, they have headlight aiming tools and guides. Badly aimed lights will be dangerous and could get you a ticket, be safe.