Mercury Grand Marquis
Heater Cores and Blower Fans
Ford Crown Victoria

How do you replace a heater core in a 1991 Crown Victoria?

222324

Top Answer
User Avatar
Wiki User
Answered
2015-07-15 21:23:40
2015-07-15 21:23:40

Drain the coolant, remove the glove box and base to the dash. youll find the heater core on the passanger side.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


The dash has to be removed to gain access to the heater box. The heater box then comes out and is split open to replace the core.

For a 1991 Ford Crown Victoria : " regular " unleaded , 87 octane

In order to replace the oil pan on the Crown Victoria you have to remove the engine from the car. After the motor has been removed then you remove the bolts holding on the oil pan and it can be replaced.

According to my Chilton's book : For a 1991 Ford Crown Victoria ( 5.0 / 302 and 5.8 / 351 ) With engine oil filter change ( 5.0 U.S. quarts )

replace heater core in a 1991 Chevy work truck 1500

Often in the owners manual is where i found the one for my 1991 Crown vic. Hope you have your manual?

On a 1991 Ford Crown Victoria : Using a funnel , you add automatic transmission fluid through the ATF fluid level dipstick ( in the engine compartment , near the firewall , on the passenger side of the engine )

In a 1991 Ford LTD Crown Victoria ( 5.0 / 302 and 5.8 / 351 ) Follow the top radiator hose from the radiator , it connects to a housing on the front of the intake manifold . The engine cooling thermostat is inside the housing

oN THE 91 FORD CROWN VICTORIA YOU WILL LOCATE THE SPEED SENSOR ON THE DRIVERS SIDE OF THE TRANSMISSION ON THE TAIL SHAFT.

No, they are not the same. The body style changed in 1992.

The Ford Crown Victoria was manufactured by The Ford Motor Company from 1955 to 1956 and again from 1991 to 2011. It is a rear wheel drive sedan and has been used as a Police Interceptor from 1998 to 2012.

The 1991 crown Victoria has several relays group in a relay center loacated under the hood near the master brake cylinder. In this relay center its the air conditioning WOT cutout relay, fuel pump, PCM power relay, and PCM power diode. P.S. defective relays must be replace as a unit.

According to my Chilton's Auto Repair Manual : For the 1991 Ford Crown Victoria : With the 5.0 litre / 302 cubic inch V8 ( 18.0 U.S. gallons ) With the 5.8 litre / 351 cubic inch V8 ( 20.0 U.S. gallons )

There is no short cut or fast way to do this. The dash has to come out to access the heater box and replace the core. So the steps in replacing the heater core are to disconnect the heater hoses, remove the dash, to access the heater box assembly and remove the box. The box then has to be opened up and the core is replaced. You will not replace the core until you get the dash out of the way. Reassembly is in the reverse order as disassembly. Fill the cooling system with new coolant, and burp the air form the cooling system.

According to one of Ford's websites : For a 1991 LTD Crown Victoria , 5.0 liter / 302 cubic inch V8 : ( .050 inch spark plug gap )

Ok, I have a 1991 Crown Vic, 5.8L-351Win, 2bbl, Police Model and the large sticker on the valve cover says "Firing Order 1,3,7,2,6,5,4,8". Hope that helps.

Try your local newspaper classifieds, eBay motors, Auto Trader, craigslist...


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.