Lexus GS

How do you replace a license plate light bulb on a 1993 Lexus GS 300?

353637

Top Answer
User Avatar
Wiki User
2008-12-06 05:33:15
2008-12-06 05:33:15

<object width="425" height="344"><param name="movie" value="http://www.YouTube.com/v/iJLbJYqV56E&hl=en&fs=1"></param><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube.com/v/iJLbJYqV56E&hl=en&fs=1" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="425" height="344"></embed></object>

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

How do you replace the license plate lights on a 2000 celica?

User Avatar

How do I change the license plate bulb on a 1993 Lexus ES 300

User Avatar

how do u change the license plate light on a 2005 sienna

User Avatar

how do you replace license pate light on 2006 pontia g6

User Avatar

The license plate light and connected right above the plate on a 2002 Volkswagen Beetle. To replace it just unscrew the old light and mount the new bulb.

User Avatar

Unscrew license plate and remove to expose light fixtures. Wedge light module away from holes. Replace them and return them to sockets.

User Avatar

It is very easy to change the license plate light on an Oldsmobile Aurora. All you need to do is remove the license plate and look above where the plate was. There are bolts that are holding the light in. Unscrew the bolts and then replace the light.

User Avatar

The license plate light on a Lexus may turn on and off if there is a loose wire. Try wiggling the wires around and see if the light goes on and off. If it's not a loose wire then the light bulb may have come loose and needs to be tightened.

User Avatar

How do you change the liscence plate light fuse

User Avatar

You can replace the license plate light bulb on a 2002 Ranger by reaching under the rear bumper and pulling out the light socket. Remove the bulb and put the new one back in.

User Avatar

unscrew the bulb in the opening above the rear license plate holder- bring the bulb to an auto parts dealer then replace the bulb

User Avatar

The license plate light on a 1995 Olds Cutlass Supreme can be replaced by accessing the bulb through a hole in the bumper next to the license plate. A person may need to do this from underneath the vehicle.

User Avatar

The license plate bulb is located right above the plate on a 2002 Oldsmobile Bravada. To replace the light simply remove the old bulb and install the new one.

User Avatar

You have to remove the liner from the inside of the trunk lid to remove the light.

User Avatar

Superdiscount LEDs has a tutorial out how to change the license plate light to an LED light. Its pretty general how to do but a lot easier with pictures. Heres to step by step links that should help you! http://www.superdiscountleds-how-to-install-leds.webs.com/ -OR- http://www.go-audi.com/14083-audi-q5-how-do-i-replace-license-plate-bulbs.html Source: www.superdiscountleds.com

User Avatar

Remove the screws from the lens covering the bulb, pull out the bulb and replace it.

User Avatar

there are two spots above the license plate where the lights go on each one there should be a spot where you can push the cover in and then just pull out at an angle

User Avatar

The license plate light circuit is protected with the tail light circuit fuse.

User Avatar

You can replace the license plate light on a 2001 Lincoln Is by carefully prying the bulb holder and turning the light counterclockwise while pressing down on it. The bulb will loosen and then can be taken out. A new bulb can be screwed into the bulb holder by turning it clockwise.

User Avatar

To change the license plate light on a 2002 Geo Tracker, remove the light lens with a small screwdriver. Take out the old bulb and replace with a new one. Tighten the screws on the light lens.

User Avatar

twist rubber housing a quarter turn pull out replace with new bulb

User Avatar

To fix a license plate light on a 1995 Dodge Colt you must first remove the screws holding the light cover in place. Remove the light from the bumper completely. Remove the license plate light bulb from its socket and replace with a new bulb. Place the light assembly back in its place in the bumper. Secure the light assembly in place with the screws you removed.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.