answersLogoWhite

0


Best Answer
Copy

What you need to do is go to an auto parts store such as AutoZone. Then buy the Wheel Bearing/Hub Assembly-Front it runs around $150. Once you have the part you need to take off the Caliper and rotor, I was able to take all of it off without taking the caliper off the rotor. Then you need a 36 mm socket to take off the cv nut. You will need a breaker bar if you don't have a tourque wrench, but remove the nut. Then take a hammer and punch, and place the punch on the cv axle and try to knock it through the hub, pushing the cv axle into the boot a little. Do not pull the hub off before loosening it from the cv axle, that could cause you to have to replace the axle boot. Once you got the cv axle free take the 3 bolts off the back of the hub. If you can't get to the 3 bolts behind the hub you can take the 2 bolts out of the top of the strut and that will give you more room. I was able to keep the strut bolts in. Once the bolts are out it may be hard to remove the hub. I had to use a lot of WD 40 and a brass hammer to get it off. However, most auto parts stores will rent you a tool that will help you take it off, the same tool will also help with getting the hub free from the cv axle if the hammer and punch did not work. Once removed put the new one on. Makes sure you put some lithium grease on everything before installation.

User Avatar

Wiki User

โˆ™ 2015-07-15 21:18:19
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you replace a wheel bearing on a 2000 Oldsmobile Alero?
Write your answer...
Submit

Related Questions

Will a wheel bearing set off a low tire pressure light in a 1999 Oldsmobile alero?

No, a wheel bearing should not set off a low tire pressure light in a 1999 Oldsmobile Alero.


How do you replace a wheel berring on an 1985 Oldsmobile regency 98?

how do you replace a wheel bearing on an 1985 oldsmobile regency 98


How many wheel bearing does and 2000 Oldsmobile alero have?

2. front left and front right.


How do you change rear wheel bearing on 1999 alero?

How do you change rear wheel bearing on 1999 alero?


How do you change front wheel bearing on 2002 alero?

To change a front wheel bearing on a 2002 Alero, secure wheels with a chock. Loosen lug nuts and lift the wheel?æwith a jack. Unscrew lug nuts and remove the wheel, the brake caliper, cotter pin, and castle nut. Remove the rotor and the hub bolts. Disassemble the hub assembly, remove the wheel bearing, and replace with new.?æ?æ


Do you need to replace the wheel bearing when replacing brake discs on a mark 4 golf gti?

no need to replace wheel bearing unless the wheel bearing is worn out


How do you change the wheel bolts on a Oldsmobile regency 98?

you have to replace the wheel bearing hub assembly look up a picture and you will see the bolts are attached to the hub assembly.


How do you replace the rear wheel bearings on a Ford Courier?

How do I put a wheel bearing on with out a wheel bearing press


How do you replace front wheel bearing on 1996 Hyundai Elantra?

how to replace front wheel bearing on 1996 Hyundai elentra


How do you replace front wheel bearing on a kawasaki mule 3010?

You can replace the front wheel bearing, on your Kawasaki Mule 3010, by removing the axle. With the axle Remove the wheel bearing will slide off.


How do i replace therear wheel bearing on a Chevy pick-up?

how do you replace the rear wheel bearing on a Chevy pick up


How do you replace front wheel bearing on ford maverick?

Take wheel off, put bearing in


What causes a thumping noise when driving a 2000 Oldsmobile Alero and when turning the steering wheel?

I just fixed this problemon A 1999 Alero... It was the front wheel bearing. You will need to replace the front wheel bearing hub assembly. Do not re-use the hub nut. Get a new one from the dealer as it's only about $10 each. The wheel hub assembly is torqued to 70 foot pound (three bolts). The axle nut (hub nut) is torqued to 173 foot pounds. Please verify the torque values with your dealer or auto part store as models years may be slightly different.


How do you replace front wheel bearing on 1992 eagle talon?

Remove the tire and wheel from your 1992 Eagle. Remove the wheel bearing nut. Remove the wheel bearing and the wheel seal. Reverse the process to install the new wheel bearing.


How do you replace a wheel bearing in a 2004 Toyota Sienna?

Is the wheel bearing on the front or the rear ????.. There is a big difference ...


How to change front wheel bearing on fiesta?

To replace the front wheel bearing on a Ford Fiesta, you will need to remove the wheel. Then with a hammer you can pull the old bearing out.


How do you replace a rear wheel bearing and seal on a 98 Toyota Tercel?

how do i replace a wheel seal


Why is your steering wheel hard to turn in your 2001 Oldsmobile alero?

Your power steering pump is likely defective.


How do you replace the front wheel bearings on a 95 Plymouth Voyager?

The front wheel bearing is a sealed unit with the wheel hub - replace the hub and wheel bearing unit. Remove the four bolts from the rear of the steering knuckle that connect to the hub bearing unit.


How do you replace the front wheel bearings on a 2003 Alero?

This would be a warranty item. Talk with your dealer. If the tires are worn out, they will make you think it is a bearing(s, and you will have went through the expense for nothing.


How do you wheel bearing for Volvo s80?

Wheel bearing are what allow wheels to spin smoothing on an axle. A broken wheel bearing can lead to fatal car accidents. To replace a wheel bearing on a Volvo s80 remove the wheel hub and have the bearing pressed out. Press the new bearing into the wheel hub to ensure a safe install.


How do you replace rear wheel bearing on a Ford Fiesta 2003?

Remove the rear tire and wheel. Remove the axle end cap. Remove the wheel bearing seal. Remove the wheel bearing. Reverse the process to install the new wheel bearing.


How do you replace front wheel bearings on Ford Explorer 2003?

How do you replace rear wheel hub and bearing.


How do you replace a wheel bearing on a 2002 Tracker?

You will need to remove the tire and wheel from your 2002 Geo Tracker. Remove the end of the axle. Remove the wheel bearing nut. Remove the wheel seal and the wheel bearing. Reverse the process to install the new wheel bearing.


How do I replace a rear wheel bearing sonata?

To replace rear wheel bearing on a Sonata, first jack up the car and grip the rear tire. Push it in and remove transmission tray and plastic cover from the suspension wishbone. Remove rear wheel, axle nut, and axle. Finally, replace the wheel bearing.