Mazda

How do you replace an antenna on a Mazda B2200 pick-up?

717273

Top Answer
User Avatar
Wiki User
2009-08-22 00:31:00
2009-08-22 00:31:00

turn your steering wheel all the way to the left, get your 10mm socket with 1/4" ratchet wobble and 2x 2" extensions and remove the several bolts holding the dust cover from inside the wheel arch. Then proceed to remove the existing broken antenna (you will need to reach up into the guard to hold the antenna) and using a 14mm ring spanner undo the topmount fitting on old antenna, Then Reverse (the antenna cable goes through the side behind glove box just trace it and replace that with new cable that comes with new antenna) or you could just cut and solder the old cable to new antenna.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

How do you replace fuel pump 92 Mazda pick up B2200?

User Avatar

behind the radiator,in the middle of the engine

User Avatar

A 1995 KIA Sportage 2.0L 16v DOHC will bolt right into the B2000 and the B2200. You will have to get a system called megasquirt from www.diyautotune.com Your Horse Power will be almost double that of the B2200 2.2L SOHC

User Avatar

The front dash speakers in the 89 Mazda b series pickup trucks are 4".

User Avatar

The torque specs for the cylinder head on a b2200 are 59-64 ft lbs (cold).

User Avatar

it con-nets to the fuel pump and the gas tank

User Avatar

Was built with R12Was built with R12

User Avatar

My 89 B2200 does this. Its like there is a dead spot in the acceleration. It is because the accelerator pump is leaking.

User Avatar

where is the fuel pump on a 89 Mazda b2200

User Avatar

Look under vehicle follow fuel line from tank

User Avatar

where is the EGR valve on a 1989 mazda b2200

User Avatar

Who is a valve calibration for mazda b2200 1988

User Avatar

The 1992 Mazda B2200 will hold close to 17 gallons of gas. The 1992 Mazda B2200 is a four-cylinder vehicle.

User Avatar

This should be located under the left drivers side kick panel.

User Avatar

MY 1992 MAZDA B2200 PICKUP RUNS GREAT FOR A SHORT TIME AND THEN SEEMS TO STARVE ITSELF WHEN I GO TO GIVE IT FUEL ALMOST TO THE POINT WHERE IT WON'T RUN IF I TURN THE ENGINE OFF FOR A FEW SECONDS IT WILL GO GOOD AGAIN BUT ONLY TO REPEAT THE PROBLEM OVER AGAIN

User Avatar

yes you can its a straight swap you don't even have to change engine mounts

User Avatar

it connects to any positive(hot wire) terminal controlled by key.

User Avatar

where is the ignition module located on a 1988 Mazda b2200

User Avatar

A Mazda B2200 engine with carburetor has 85 horsepower, and with fuel-injection has 105 horsepower.

User Avatar

behind the fuel tank you will see a clamp this is where the filter goes at least it is there on my 1989b2200

User Avatar

Coolant temperature sensor is locatedat the front of the intake manifold near the upper radiator hose.

User Avatar

how du you replace a thermostat in Mazda pickup b2300 94

User Avatar

The valve guides in the cylinder head wear out and oil gets sucked in and burned.

User Avatar

Yes, a Mazda B2000 is most definitely a 4-cylinder with a 2.0L engine. However, technically Mazda didn't produce the B2000 as a 1988 model. It was made in 1986-1987. Then in 1989 Mazda made the B2200 Pickup, which is a 2.2L 4 cylinder.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.