answersLogoWhite

0


Best Answer

The oil pressure sending unit is located right above the oil filter.

User Avatar

Wiki User

โˆ™ 2007-07-21 21:58:34
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides

๐Ÿ““
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How do you replace an oil sending sensor on a 96 Mercury Villager where is it?
Write your answer...
Submit
Related questions

How do you replace the odometer cable on 1998 Mercury Villager?

You don't as it does not have a cable. You replace the speed sensor instead.


Should one purchase a 1998 mercury Villager if speed sensor is needed?

The speed sensor is not expensive and is easy to replace.


How do you install a knock sensor in a 1993 mercury villager?

the elictronic control sinsor at on a 93 mercury villager


How much does a cam sensor on a 96 mercury villager cost?

The cam sensor on a 1996 Mercury Villager cost about $35 to $40. The sensor is actually manufactured by a Nissan subsidiary.


How do you replace a knock sensor on a mercury villager estate 3.6 engine?

There's no need to replace knock sensors, and there was never a 3.6 engine.


How do you replace the speed sensor on a 1999 Mercury Villager?

The speed sensor is on the top back corner of the transmission housing. It is held down by one screw.


Where to find and how to replace a DPFE sensor on a mercury villager?

I'm not aware that part was installed on Villagers. It would be on the EGR valve if it was.


How do you replace 1994 mercury villager tps cable?

TPS usually means throttle position sensor, and it doesn't have a "cable".


2001 Mercury Villager V6 3.3 Crank Position Sensor?

the sensor on the 3.3l mucury villager is integrated into the distributor


Where is the transmission speed sensor located on a 1998 mercury villager van?

on my 1999 ford mercury villager its on top of transmission under the van


How do you replace oxygen sensor on a 1999 mercury villager sport?

Unplug the sensor and unscrew it from the exhaust pipe. You'll probably need a special socket to do it without damaging the wires.


Is there more then 1 CKP sensor on a 2000 Mercury Villager?

No, there is not.


Where is the fuel temp sensor on a 2000 mercury villager?

There is no such part.


Show where the knock sensor located?

can you tell me where the knock sensor is located on a 3.3l mercury villager


Replacing Mercury villager speed sensor?

The speed sensor is at the top rear of the transmission housing.


Where is the fuel sensor mercury villager?

If you mean the fuel level sensor it's in the fuel tank.


What does the knock sensor look like on a mercury villager?

This is an image. (below)


Where is the mass air flow sensor on a 1998 mercury villager?

In a 1998 Mercury Villager, the mass air flow sensor is located in the air intake tube. The air intake tube goes from the air box to the intake.


How do you replace cam shaft indicator 2000 Mercury Villager?

The camshaft position sensor is an intregal part of the distributor, therefore if the CMP sensor is defective the distributor must be replaced. Have it checked out by a qualified mechanic.


Where is the outside temperature sensor located on a 2000 Mercury Villager?

In the engine compartment


Where is the cam position sensor on a 2001 Mercury Villager?

It is located in the distributor unit.


Where is the sensor for the rear hatch on a 1996 mercury villager?

That is incorporated with the latch assembly.


Where is the speed sensor on a 2001 Mercury Villager?

Top rear corner of the transmission.


Location of knock sensor on a 99 Mercury Villager?

It is under the intake manifold.


How do you install a throttle position sensor on a 1998 mercury villager?

remove and reinstall