0
Take off the cover on the left side of the saw that holds the pull cord. You should now see the plastic base of the bulb, with two Allen-head screws holding it in. Take out the screws and it should come out, still attached to the fuel lines. You may need to use very long, fine needle-nosed pliers to take off the fuel lines. Reverse all this to install the new one. You can buy a new bulb over the internet, but your local small engine repair shop can probably sell you one cheaper (and faster). Hope this helps.
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
How do you replace the primer bulb on the snapper S31SST weed eater?
www.odref.com/poulan/pdf/snapper/all/s31sst.pdf
How do I replace a cracked primer bulb of Eager Beaver 2014 chainsaw?
Check with Ebay, I found one there.
What causes gas to come out the primer bulb?
A cracked primer bulb. You will need to replace it.
How do you replace poulan chainsaw fuel line?
I'm having the same problem with my Poulan chainsaw and weed eater. I think the line starts with the fuel filter in the tank and travels up to the primer bulb, out of the bulb into the carburetor, and out of the carburetor back to the tank. Whatever the size of line is that hooks to the fuel filter is what will hook to the primer bulb and then the carburetor. Then one more single line returns to the tank. I may not be correct on this, but there's not much information available. The diagram on Poulan's website does not show the routing of the fuel lines. that is right but to remove the main line you need to drain fuel and pull the line out from the fuel tank neck first because it has a connection that will not fit threw the hole in top. to replace it cut new line at a slaint and fir it threw from the top down into the fuel tank. then keep it long and pull out enough threw the fuel cap to put fitting back on it and fuel filter then pull it back threw and hook it to primer bubble. Not sure about your answer I have two different size fuel lines on mine. The larger line if I remember correctly runs from primer bulb to the right of fuel tank where the larger opening is located. The smaller line is where I am confused at shouldn't the smaller line from the fuel tank that has in tank filter attached run up to carburetor. then a smaller line from primer bulb to second fitting on carb. byrumjr the line starts with the fuel filter in the tank and travels up to the carburetor out of the carburetor into the primer bulb, out of the primer bulb back in the tank
How do you replace primer ball to gas tankto my McCulloch chainsaw mac3200?
It is simply held in by plastic tabs on the primer bulb. All you have to do is pry behind it and easily pop it out with a flat screw driver.The tabs break easily but replacment primer bulbs are available.http://store.chainsawr.com/
How do you replace fuel primer bulb on 32cc weed wacker?
primer bulb replacement on craftsman 32 cc week wacker
How do you Route fuel lines on a Poulan chain saw?
long line with filter goes from gas tank into carb shorter line goes to (INLET) suction side of primer bulb 3rd line goes from OUTLET side of primer bulb to other carb fitting
What is the fuel line routing on a poulan 2375?
The small line from the tank (with the fuel filter) goes to the top port of the carburetor. The large line from the fuel tank goes to the center port of the primer bulb. The other port of the primer bulb goes to the bottom port of the carburetor.
How do you repair a leaking primer bulb on a craftsmen snowblower?
You don't. They are not difficult to replace.
A diagram for fuel lines for a poulan woodshark 1950?
Make sure you have the lines wright the skiney line from in the tankgoes to the top nipple on the carb the over flow line goes to the long nipple on the primer bulb and the other line off the primer bulb goes to bottom nipple on carb
How do you repair leaking fuel primer bulb on Toro lawnmower?
Don't know that a leaking primer bulb can be repaired. Most likely, you have to replace it. You don't want to forget the routing of the fuel lines!! You might want to make a drawing of the routing before you remove the primer bulb.
What is the routing for the fuel lines on a poulan 2050 wild thing chainsaw?
There are two lines inside the tank. The short line with no fuel filter on the end of it goes to the inlet, (suction) side of the primer bulb. The long line inside the tank, with the filter on the end goes directly to the fitting on the side of the carburetor. The line, inside the air box from the outlet side of the primer goes to the remaining fuel line fitting on the carburetor. http://store.chainsawr.com/
