answersLogoWhite

0


Best Answer
Copy

Idk about the 99 civic but on my 95 jdm d15 the crank shaft position sensor is in the distributor. If the sensor is bad then you must replace the whole distributor. A bad wire could also cause this problem. Hope that helps good luck. jdmd15crx

User Avatar

Wiki User

โˆ™ 2008-03-08 18:12:04
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you replace the crank shaft position sensor on a 99 Honda Civic?
Write your answer...
Submit

Related Questions

Average cost for replace throttle position sensor on 2001 Honda Civic ex?

My wife is paying 441.00 for her Honda civic '05.


How do you replace 02 sensor for Honda civic lx 1998?

i dont no


Where is the crankshaft position sensor on a 2000 civic ex?

The crankshaft position sensor can be found on the bottom of the engine in a 2000 Honda Civic EX. It is next to the crankshaft itself.


Where is the crankshaft position sensor on your Honda civic 1991 located?

inside the distributor


Where is the knock sensor on a 2001 Honda Civic LX 1.7 L engine?

knock sensor position


Where is the 1995 Honda Civic crank position sensor?

behind the timing belt covers


What is function of throttle position sensor for Honda civic?

the throttle sensor function is to stabilize the ref of the car engine


Where is the location of TPS sensor in Honda civic hatchback 1989?

The Throttle Position Sensor is located on the throttle body


Where is the LAF sensor located on a 92 Honda Civic?

Where is the LAF sensor located on a 92 honda civic?


How do you replace thermostat on Honda Civic?

how do you replace thermostat on 1994 Honda civic dx


How do you replace oxygen sensor in Honda civic?

The oxygen sensor on a Honda Civic is replaced by disconnecting the wiring harness and removing the sensor using a socket wrench. Anti-seize paste is applied to the threads, a new sensor is torqued into place, and the wires reconnected.


How do you replace abs wheel speed sensor 1994 civic VTi?

The speed sensor on a 1994 Honda Civic is located on top the of the transmission. To replace it unplug the sensor from the wire harness then the remove mounting bolts and assembly from the transmission.


How do you replace CO2 sensor in civic?

The O2 sensor on a Honda Civic is found on the exhaust system. It will be mounted near the catalytic converter. Simply unscrew the sensor from the exhaust pipe and unplug it from the wire harness. Replace with a new unit.


Replace air filter on a 2004 Honda Civic?

replace air filter on a 2004 Honda civic


How do you remove speed sensor on 92 civic?

The speed sensor is found on the transmission of the 1992 Honda Civic. To replace the unit locate the mounting bolts and remove them. Unplug the wiring clip and pull the sensor off.


Where is the iat sensor on a 95 Honda Civic?

See for yourself in this pic for a 95 Honda Civic


How do you replace a clock spring on a 1995 Honda Civic?

how to replace a clock spring in a 95 honda civic ex


How do you replace ac belt 1996 Honda civic?

how do you replace a/c compressor for 1996 honda civic 1.6L


Where is the Camshaft Position Sensor located on a 2005 Honda Civic?

take off timing belt cover....it is below it.


What causes 1998 Honda civic o2 sensor heater circuit code?

9 time out of 10, the heater circuit internal to the sensor has failed. Replace the sensor.


You replace the iat sensor fron a Honda civic vt and reset the check eng light but do not clear the code still in?

problem is not sensor but is in wiring to sensor or computer


How do you replace the o2 sensor in 92 Honda civic?

Remove the vacuum hose from the sensor. Remove the sensor retaining screws. The sensor will come off. Reverse the process to install the new sensor.


How do you replace Honda taillight bulb?

how do you replace a taillight on a Honda 2002 Civic?


Is ckf crank fluctuation sensor and ckp crankshaft positioning sensor same for Honda Civic vtech sport 2000?

No the ckf and the ckp are not the same sensor for a 2000 Honda civic. The crank fluctuation sensor is behind the crank pulley and can be changed fairly easy with some mechanical knowhow when the timing belt is done. The crank position sensor is built into the distributor. To change this sensor you would have to rebuild the inside of the distributor or replace the entire distributor. Hope this answers your question.


Reset 2008 Honda Civic after tire change?

how to reset a tire sensor for a 2008 Honda civic si