answersLogoWhite

0


Best Answer

I would suggest you obtain a HAYNES manual from a NAPA store as this is detailed and your personal safety involved due to air bag .

Answer --- Just pry out switch with something like a .020" thick feeler gauge, andunplug it.

User Avatar

Wiki User

โˆ™ 2008-11-24 06:47:55
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How do you replace the cruise control on off switch on a 2002 LeSabre?
Write your answer...
Submit
Related questions

2001 Buick Lesabre The cruise control wont work unless you keep the the on button held down while you hit sit cruise. How do you remove the Switch?

Replace the cruise control switch (the one with the orange light in it) The switch is a push on push off. If the little plastic gear inside the switch breaks off the switch will work like a door bell switch and will not latch on.


How do you repair the cruise control on a 1994 Buick Lesabre Limited?

First you need to troubleshoot the 1994 LeSabre cruise control. Check the fuse, the cruise switch, the linkage, to find where the problem is. Check the vacuum lines on the engine as a vacuum leak can cause the cruise to not work properly.


What needs to be done to remove and replace the combination turn signal cruise control wiper and headlight dimmer switch on a 2000 Silverado?

The combination turn signal, cruise control, windshield wiper, and headlight dimmer switch simply plugs in. Pull the relay switch out and replace with the new switch.


Cruise control switch Chrysler sebring?

The Chrysler Sebring cruise control switch is located beneath the dashboard, on the drivers side. The cruise control switch should be labeled as such.


How do you replace a turn signal switch on a 1990 Buick LeSabre?

It is quite simple to replace the turn signal switch on your 1990 Buick LeSabre. The turn signal switch simply plugs in and out.


Why is my Cruise control on ford taures stuck on?

This means that the switch is going bad. You will need to replace the switch that is on your steering wheel or on the turn signal switch.


How do you replace the cruise control switches on a 1999 Ford Ranger?

i need a top cap button for the on-off switch for the cruse control


Does brake switch control cruise control?

On most vehicle the brake switch is one way to shut the cruise off.


Disable cruise control?

Most cars have a switch to disable the cruise control. To permanently disable the cruise, remove the fuse for the circuit.


How do you repair cruise control on 1992 Grand Pr ix when it is not the fuse?

Change the cruise control switch.


1987 300zx cruise control does not work?

If the cruise control on your 1987 300ZX does not work, you might have an issue with the cruise control fuse or wiring. You could also have a problem with the switch that turns the cruise control on and off.


When the cruise control goes out of a 2002 ford windstar what do you replace?

That depends what is wrong with it. The first thing to check would be the brake switch.


Where is cruise control relay on 1994 F150?

The cruise control relay on a 1994 F150 is operated by a switch behind the horn pad and airbag on the steering wheel. The switch will probably need replacement if the cruise control in your vehicle is malfunctioning.


Where is the cruise control switch located for the Lincoln town car 93?

The cruise control switch on a 1993 Lincoln Town car is attached to the master brake cylinder under the hood. Ford had a recall on this car because the cruise control switch could lead to a fire.


What could cause that the cruise control switch doesn't work in your 02 impala?

most cruise control problems are caused by a leaking vaccum canister that controls the throttle on the cruise, your switch is probably fine.


How do you repair the switch for the bright lights for a 1992 Buick LeSabre?

replace the combination switch on the turn signal stalk


how to replace the switch?

replacing the volume control switch on 2008 flhx how to replace the volume control switch on 2008 flhx


How do you fix cruise control on a 1994 Chevy pickup?

Find out what's wrong, then repair it or replace it. There, that was simple. And the fact is, that's what ALL repairs are about. Cruise control problems are often quite simple, such as a faulty brake light switch or cruise control activation switch or even a poorly adjusted cruise control module. But you'll need to start looking at the individual components and find out which part isn't doing what it's SUPPOSED to be doing.


Is there a fuse for Cruise Control for 2000 Chevy Express Van?

No. The Cruise Control is controlled by the engine ECM. If your cruise control isn't working, you probably either have a bad switch to actuate the cruise control, or a brake pedal switch which is in constant contact, and thus telling the computer it's engaged when it isn't.


Does MY Astra have a clutch switch for cruise control?

Yes


Why did my cruise control quit working after I change out my BOO switch on 98 mustung?

The most probable cause for your malfunctioning cruise control is a blown fuse. The fuse might have blown while you were changing your switch. The cruise control fuse can be found in the fuse box.


Where is the on off for the cruise on a Jaguar X type?

On the right interior of the steering wheel, there is an on/off switch and a stop/resume switch for the cruise control


What is a speed control deactivation switch?

It's near the brake pedal or brake light switch.... It deactivates cruise control


What is the small silver switch for located in front of your left shin above the brake peddle in a 1989 MGM?

There are two. The brake light switch and the cruise control cut off switch. You are probably talking about the cruise control cut off switch. When you depress the brake pedal, the brake lights come on and the cruise control stops. Hope this helps


How do you install a brake light switch with cruise in a 1990 Jeep Cherokee?

Start by removing the connections for the cruise control and brake lights, then remove the bolt that holds the switch to the brake pedal. Once the brake pedal is loose the switch is held on the brake pushrod by a bushing with nylon retaining washers. Carefully remove one washer and slide the bushing out, the switch can now be removed from the pushrod. Installation is the reverse; line up the hole on the switch with the hole on the pushrod, make sure the tabs for the cruise control and brake lights are facing properly. Reinstall the bushing and replace the other nylon washer, replace the bolt and tighten. Lastly connect the brake lights and cruise control.