Brake Pads and Rotors
Ford Tempo

How do you replace the front brake pads on a 1994 Ford Tempo?

909192

Top Answer
User Avatar
Wiki User
2011-09-12 20:56:25
2011-09-12 20:56:25
Front brake job. 1994 ford tempoWhen you pull the tire off take a #T30 Star Key not an Allen key to remove the brake caliper. Check the rotor see if its needs to be cut or replaced. Put your freshly cut rotor on or new rotor on. After this take a C-Clamp and a socket (any size deep recommended) and start tightining the C-Clamp to recomprese the piston on your caliper. If the caliper doesn't easly comprese the piston is seized and your going to have to replace the caliper, if the piston compreses put your new brake shoes/pads on starting with the rear pad (the small one) then the front (the bigger one). Slide the caliper on and tighten the star keys and your done.

P.S Take the caliper off starting with the top first then the bottom and do the exact opposite to put it back on.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

How do you replace the PCM ON A 1994 Ford Tempo GL?

User Avatar

Lift the car on a jack, remove the tire, remove the brake shoe/caliper and remove the brake pad. Put in the new brake pad, replace the brake shoe/caliper, replace the tire and lower the car.

User Avatar

I would like to change the blower motor in my 1994 Ford Tempo by myself. Do you have any instructions for me to follow?

User Avatar

Lift the car, remove the tire and set aside, remove the brake shoe/calipers and remove the old pads. Replace the old pads with the new pads, replace the brake shoe/calipers, replace the tire and lower the car.

User Avatar

Lift the car, remove the tire, remove the brake shoe/caliper and remove the old brake pad. Put in the new brake pad, replace the brake shoe/caliper, replace the tire and lower the car to the ground.

User Avatar

Lift the vehicle on a jack, remove the tire and put it aside, remove the brake shoe/caliper, and remove and dispose of the old brake pad. Put in a new brake pad, replace the brake shoe/caliper, replace the tire, tighten the nuts, and lower the vehicle to the ground.

User Avatar

you will have to disassemble the rear lens by entering the trunk. If the question really is for a 1998 Ford Tempo, then the answer is - you can't because the last Ford Tempo model year is 1994!!

User Avatar

Do you see ABS on the dash screen when you start it up?

User Avatar

how to change front brake pads on a 1994 lexus es300

User Avatar

I need to replace the disc brakes on my 1994 Cadillac eldorado touring coupe? could you supply a diagram of this producure?

User Avatar

there is a pin on the switch which must be depressed to remove the unit from the dash.

User Avatar

AnswerMost likely, because your brake fluid is low in the master cylinder or leaking due to a faulty seal or fluid line. However, check the thickness of the front brake pads, if they are worn, replace them, for as the brakes wear fluid level drops in the cylinder, but when the piston is pushed back in the level will rise. Further, perhaps the parking brake cable is loose or disconnected from the cabin floor mounted lever. This would cause the lever to move. Therefore, making the brake switch to turn on the dash light.

User Avatar

Lift the car, remove the tire and set it aside, remove the brake shoe/caliper, remove the brake pad and dispose of it. Put in the new brake pad, replace the brake shoe/caliper, put the tire back on the car, and lower the car to the ground.

User Avatar

The Ford Tempo was introduced as a 1984 model to replace the Ford Fairmont. Then it was replaced by the 1995 Contour. That's a production run of 10 years. (1984-1994).

User Avatar

Could be the tires, or your front brake rotors

User Avatar

On all Harleys with disc brakes the front brake switch is located inside the right handlebar switchbox.

User Avatar

Remove the tire and wheel from your 1994 Chevy Lumina. Remove the brake spring and the break caliper. The brake pads will come off. Reverse the process to install the new brake pads.

User Avatar

On the older model Tempo the relay was located in the front seating area, driver side, under dash, mounted above fuse panel.

User Avatar

Jack the front end up of your 1994 Ford F2 50. Remove the tire and wheel. Remove the brake pads and assembly. Tap on the rotors until they are loose. The rotors will slide off. Reverse the process to install the new rotors.

User Avatar

Changing brakes is a simple task. Lift the car, remove the wheel, remove the brake shoe, replace the pad, replace the shoe, replace the wheel and lower the car.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.