How do you replace spark plugs on a 2004 Sable - Taurus?
It's under the front right headlight, need to remove headlight assembly and cut hole to get to relay, which is under the plastic frame that holds headlight assembly. The other option is to remove the front bumper assembly to access. If the relay repeatedly fails the fan motor will need replaced.
i need to replace a throttle sensor and put a throttle body rebuild kit in
in the engine compartment on the firewall right in front of the passenger and right behind the coolant bottle.
Reach behind the bumper of the 99 Cavalier. There are two nuts that hold the turn signal assembly in. Remove the nuts to take the assembly off and replace it.
after you order the right parts, there are a few screws that hold the capsule in. make sure you have taken out the bulb and unplugged it. the assembly should come right off.
I just changed the whole headlight assembly in my 1997 grand caravan. However, to change the parking light or turn signal indicator light, there is a round plastic plate in the front fender well in front of the tire. Pop this out and reach in and unplug the socket from the light assembly, change the bulb and install in reverse order. Good luck!
Jack up and support the right front of the vehicle. Remove the wheel/tire. Remove the brake caliper and hang the caliper with a piece of wire out of the way. Remove hub/rotor assembly. Remove backing plate and spindle. Slide out axle assembly. Replace u-joint as you would on a driveshaft. Assemble in reverse order.
To replace the front turn signal bulb in a 2005 Montana, you have to access it from the engine compartment. Undo the front headlight assembly as per the instructions noted elsewhere. There is one screw (machine Head) on the outboard side of the headlight assembly, and one 'thumb screw' on the inner side to the assembly. I found it difficult to remove the headlight assembly, and I have found you don't have to. (You can break the housing, so don't try taking it right out) Just loosen it enough to get your hand behind the assembly. I would also suggest you remove the plastic fasteners from the top of the front bezel in order to make loosening the headlight assembly easier, and to prevent the possibility of damaging or breaking the front bezel. The plastic fasteners are easily removed with just a pair of pliers. Once the headlight assembly has been moved forward slightly, you can get your hand down the opening, and feel for the turn signal lamp assembly. Twist to remove. There is enough wire in the harness to bring the lamp assembly to 'the surface' where you can replace the bulb easily. Replace bulb and test. After testing, replace headlight, and then plastic fasteners at the top of the front bezel.
For the front there is a tiny bolt above and to the outside of the headlight assembly that screws thru the fender into the turn siignal assembly. For the back the assembly is screwed in by 2 screws on the tailgate side and 2 screws on the outside.
Here is a hint, ask a dealer!
how to remove, or replace front right axle escape 2004
There is a long bolt on top of the headlight/blinker assembly. Remove this bolt and slide the entire headlight/blinker assembly out just enough that you can see the bulb socket. Twist the socket and it will pop right out.
Each of the headlight assemblies are braced through the radiator support with a pair of retainers. The retainers for the right headlight assembly are in front of the battery. The retainers for the left assembly are in front of the washer fluid reservoir. Remove the retainers by pulling up on the retainer. With the retainers removed, the headlamp assembly falls forward. Reinstall the retainers to the square tabs on the headlamp assembly and the rivet on the radiator support
if i remember right a 2004 grand prix is a front wheel drive motor so it wouldn't have a read axle just rear wheel bearing
on what car
That's really easy, it's right there on the front of the jeep, right below and behind the bumper, unbolt both ends and replace. Even easier than doing shocks because it's so easy to get to.
trouble putting right front signal bulb in.
it's under the throttle body ,(air intake) on right side(back of the motor)pully and belts is on the leftside(front of motor)1999 grand am 3.4 sfi.
i am guessing that you want to change the bulb and not the assembly. to remove the bulb just turn it to the left remove the old bulb replace in the assembly but this time turn it to the right.
How do u replace the front axel on a 1997 nissan altima
Start at right rear, then left rear, right front, and end at left front.
Right rear, Left rear, Right front, Left front was the standard procedure.
If you lift you rear hatch there are 2 torx screws (I think that they are t30 or t35 ) Just remove them. You must then pull the lens strait out there are two pins holding it on. 2nd opinion: So we are talking about the REAR tail light assembly, as opposed to the FRONT tail light assembly, right? Have you ever seen a "cow" with it's tail in the front?