answersLogoWhite

0


Best Answer
Copy

Hey pete==It is quite complicated. Get a manual on your car and it will have pictures and everything. GoodluckJoe

Replacing the head gasket on any vehicle is a long and complicated process, however if you wish to see basic step-by-step instructions go to the related question on the right side of the page "How do you replace a head gasket?"

User Avatar

Wiki User

โˆ™ 2015-07-15 19:20:33
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you replace the head gasket located on a 1990 VW Passat?
Write your answer...
Submit

Related Questions

How do you replace the valve cover gasket on a 1990 Honda Accord?

How much does it cost parts and labor to replace a valve cover gasket on a 1990 Honda Accord 4door.


How do you replace a head gasket on 1990 Pontiac lemans?

You don't


How do you replace the head gasket located on a 1990 Chevy Cavalier?

Replacing the head gasket on any vehicle is a long and complicated process, however if you wish to see basic step-by-step instructions go to the related question on the right side of the page "How do you replace a head gasket?"


How do you fix a blown head gasket on a 1990 Toyota Supra?

Replace the head gasket is the only fix.


How do you replace a stock radio on a 1990 v w passat?

Insert 4 small pins in the holes on the front of the radio and pull out.


How do you replace the water pump on a 1990 Chevy Corsica 2.2L?

Where is the Water Pump located and how do you replace it on a 1990 Chevy Corsica?


Does head bolts have to be replaced after replacing head gasket on 1990 Honda accord?

Yes, replace the head bolts.


Where is the thermostat located and how do you replace it located on a 1990 Buick Century?

inside the radiator hose


How do you Replace oil-pan gasket on 1990 Buick skylark?

I have a 1990 Buick Skylark and I need to remove the oil pan. How do you do it ? Help!! Just remove the spash shields in the way of the pan then remove the bolts from the pan and replace the gasket. You can find Buick manuals from Chiltons on Amazon for these cars. They're cheap nowadays.


How do you replace the fuel pump on a 1990 Honda Accord EX?

It is located in the fuel tank. The tank must be removed to replace it.


How do you change the intake manifold gasket on a 1990 Chevrolet c1500 silverado?

remove the air filter pan assembly and the 15-20 intake bolts clean gasket area replace n re bolt down


How do you replace the headlight bulb located on a 1990 Toyota Celica?

Take out the headlight is the easiest way!


Where is the fuel pump on a 1990 passat?

My 92 has the pump inside the fuel-tank


How do you replace and install ignition relay for a 1990 Honda Accord?

If you haven't replaced the relay, check this website. It will show where it is located and how to replace. autorepair.about.com


How do you replace the differential gasket on a 1990 Chevy scottsdale 1500 series pickup truck?

If you look up under the back of the truck at the rear end housing, you will see a round plate with at least 10 bolts in it. Take all the bolts out. When you remove the plate grease will run out. Clean old gasket off, replace with new gasket, Put plate back on and fill with grase.


How do you replace the valve cover gasket on a 1990 Honda Civic 1.5L FI and how much would it cost?

First remove spark plug wires from the top of the valve cover. then remove bolts or nuts around the edge of valve cover. once removed. take off cover and replace o-rings and gasket. gasket is located around edge of cover and o-rings are o shaped rubber gaskets on the cover around the holes where the wires normally go through. be sure to replace cover the same way you remove it. estimated cost would be $35 for just gasket and 0-rings it is recommended to also replace wires and spark plugs when doing this.that cost would be 60-$90 depending on make of vehicle.


Where is the fuel filter located and how do you replace it on a 1990 Chevy Camaro?

In front of left rear tire under body


How do you replace a 1990 Chevy Beretta battery?

how to replace a 1990 Chevy Beretta battery


Where is the knocking sensor located on 1990 Toyota 4Runner?

Its located deep inside the motor, between the heads. You have to dismantle the the whole top of the motor to get to it. I just had a blown head gasket repaired, and the mechanic showed me the knock sensor and said that while the heads were off and the engine was stripped down, and he could actually get to it, that I should replace the wires leading to the sensor.


Where is the cooling system thermostat on a 1990 Mercedes 560 SEL?

it's located on the engine . or take it to the dealer . if you don't know what you are doing . those vehicle are expensive . if i were u . i take it to the dealer . Easy there! The thermostat is on top of the water pump and is a simple fix. You need an "O" gasket when you replace the thermostat.


How do you replace a water pump on a 1990 BMW 325i?

How do you replace a waterpump on a 1990 BMW 325i


How do you replace the fuel pump in 1990 dodge grand caravan?

Should be located in the fuelk tank- may have to remove for access


What would cause the power windows to automatically roll up when the car is shut off on your 1990 VW Passat?

it could be that your relay is stuck on. your passat windows can be lowered or raised when car is off.


How much does it cost to buy a head gasket for a 1990 240sx?

It costs between 30-40 dollars for the head gasket itself.


How do you replace the head gasket located on a 1990 Toyota truck?

This is a fairly easy engine to replace the head gasket on, but it's very very important to make sure the surfaces are both clean and flat! 2 things you really need to invest in are a decent torque wrench (sears/crafstman has a good one for a decent price) and a haynes manual. There's a very informative writeup in the haynes. It depends which engine the truck has. If it is the 4cyl. it is a several hour job, if it is a 6 cyl. it is twice as long, major work. No way to describe it here. Replacing the head gasket on any vehicle is a long and complicated process, however if you wish to see basic step-by-step instructions go to the related question on the right side of the page "How do you replace a head gasket?"