The headlamp assembly just snaps on and off. There are four attachments (one in each corner). Give the assembly a firm pull out, and it should pop on out
You remove the two screws on the top of the lense. You then pull the lense forward. There are plastic clips on the back that will release. You can now get to the bulb.
I'm trying to replace the headlight assembly for a 2000 Jeep Grand Cherokee Lerado. What bolts or screws do I remove
Be more specific. You can get asemblies for 99 and newer on eBay for 80 dollars a set...brand new
If it's like my '95 (which it should be), the entire headlight assembly just pops out. There are three connectors: two in the bottom corners and one in the top outside corners. They may be difficult to pull out, but just keep pulling. They'll come out.
Undo the hex nut on top of the headlight assembly and remove bolt. Grap bottom front of headlight assemby and pull hard upwards causing the bottom pins to release then pull directly outwards to release the top pins. Turn back of globe anti clockwise to release globe from headlight assembly.
Ignore that previous answer, he probably thought of removing the clear lens from the black housing... Yes, you can replace the headlight cover. The assembly is just pushed into three ball snaps. First from the engine compartment unscrew the bulb and pull it out, second with two thin pry bars lightly pop out the assembly, it its only as big as the lens squared, They can be purchased as a new headlight assembly (which is just the one lens with the black plastic inner shroud the bulb screws into.) Once you have it out it will appear so simple and just snap back into place the new one and screw in the bulb. I bought two new ones on EBay for $20.
I'm trying to replace the headlight assembly for a 2000 Jeep Grand Cherokee Lerado. What bolts or screws do I remove
The piece that a headlight assembly snaps into on a Jeep Grand Cherokee is called a headlight collar. It is also called a headlight assembly.
Not possible. You have to remove the whole light assembly.
No, they are part of the headlight assembly.
It's under the front right headlight, need to remove headlight assembly and cut hole to get to relay, which is under the plastic frame that holds headlight assembly. The other option is to remove the front bumper assembly to access. If the relay repeatedly fails the fan motor will need replaced.
the relay is behind the r/f headlight assembly. remove it and the grille it will be below the assembly mount 3 wires green, green andwhite, and brown i think
Here is a guide to follow: http://98jeepbuild.blogspot.com/2009/06/cant-see.html
I need to replace the bulb on the driver side of my 2003 Dodge Grand Caravan. After searching this forum I found a similar question regarding the 2000 Caravan. It talked about under the hood removing three screws and pulling out the headlight assembly. I tried this and it worked on the 2003. 1) open the hood. 2) Carefully remove the three screws holding the headlight assembly in place. In my case the screws were black. Be careful as they are screwed into plastic. 3) Carefully slide the headlight assembly out. At this point you can replace the headlight bulb, turn signal bulb, or the entire headlight assembly. To replace the headlight bulb turn the collar holding the bulb in counter clockwise. Pull the bulb out of the headlight assembly. Replace the bulb. Insert the bulb into the headlight assembly insert the collar and turn clockwise until it locks. 4) Carefully insert the headlight assembly back into place. 5) Replace the three screws removed in step 2 being carefull not to over tighten.
Be more specific. You can get asemblies for 99 and newer on eBay for 80 dollars a set...brand new
for a 1994 Grand Caravan (probably like the 1995) see: How do you replace the headlight assembly located on a 1994 Dodge Caravan? for a 1994 Grand Caravan (probably like the 1995) see: How do you replace the headlight assembly located on a 1994 Dodge Caravan?
To replace a turn signal on a 1994 Jeep Grand Cherokee prop the hood open. Locate the headlight housing and the turn signal will be located next to it. Find the bulb and remove it from the housing. Replace the bulb.
Take out the 6mm bolt and pull outwards on the headlamp assembly.