Chevy S-10
Heater Cores and Blower Fans
Chevy Blazer S-10

How do you replace the heater core for a 2001 Dodge 1500 pick-up with passenger side airbag?

272829

Top Answer
User Avatar
Wiki User
Answered
2015-07-15 18:59:13
2015-07-15 18:59:13

Is it still under warranty? If not, then you need to go to a car parts store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.

001
🙏
0
🤨
0
😮
0
😂
0

Related Questions


you need to take apart the lower dash on the passenger side. This is not a fun job.

i need to know how to replace the heater core on my 1992 s-10 pickup

The switches are in the bottom of the driver and passenger front seat. When someone is sitting in it, it's on.

Give us the symptoms you are experiencing with your 2002 S-10? or Silverado? Such as, leaking coolant on passenger floor. lack of heat. sweet smell when heater is blowing.

pay someone to do it for u, what a pain in the ARSE

You can reset your Chevrolet 2500 pickup truck airbag warning light by removing the airbag warning light fuse. Keep the fuse out for 10 seconds and replace it to its original slot.

Pull the top off of the black box on the passenger side of truck under the hood. Remove the two heater hoses. Remove the old heater core. Reverse the process. Top off the radiator with antifreeze and check again after a test drive. Enjoy the heat.

You should probably bring it to a mechanic because it is very difficult to replace the heater core on GMC pickups.

The heatercore is located on the passenger side under the dash. It is located on the left side of the blower fan. Remove the heater core housing which consists of 5-6 screws. Disconnect the two radiator lines under the hood that run into the firewall. There should only be one bracket holding the heater core in the housing. Remove and replace the heater core in the opposite order. Have a good one.

Remove the glove-box door. Behind that is the heater core cover on the interior, passenger side of the firewall. Remove that cover and there is the heater core. Open the hood and look where the heater hoses enter the front right passenger area of the exterior side of the firewall. Disconnect the two heater hose clamps and you can then remove the heater core.

The 1993 Ford F1 50 pickup truck heater core can be replaced by removing the water supply hoses. Remove the heater core retaining bolts. Reverse the process to replace the new heater core.

You first have to drain the radiator, then you diconnect the heater hoses to your heater core .in the engine compartment. Then you remove the cover off the heater core assembly under the passenger side , under the glove box. Then you take straps off the heater core off. and replace . Install every thing you removed previously and refill your radiator and your done.

Remove the water from your 1987 Nissan pickup truck cooling system. Remove the water supply hose. Remove the water return hose. Remove the heater core retaining bolts. Reverse the process to install your new heater core.

You dont. You just have to remove the glove box insert.

Blower motor resistor assembly is located under dash board on passenger side.

Im in the same boat as you are but i think you have to disable the airbag and drop the steering wheel to reach it

The small trucks do not have an airbag.

take out the glove box and 4 screws that hold the cover around the heater core and take off the 2 heater hoses under the hood

I couldn't replace just the bulb. You have to buy a whole new lamp. $5-10 at autozone.

( IF ) it has an on / off switch for the passenger airbag the switch will be just to the right of the radio near the bottom of the radio on a 2001 Ford F-150 Insert your ignition key and turn the switch to the OFF position . Hold the switch in the OFF position while you remove your key

To many steps involved to list here. I would suggest purchasing a shop manual for that vehicle if you want to replace the heater core yourself.

The heater core is behind the AC evaporator core. You must remove the panel with the venting on the passenger side. Then you must disconnect the two AC fittings inside the engine firewall. You do not have to remove the AC evaporator core, it will swing somewhat out of the way so that you can get to the heater core. There are several clips and screws holding the heater core in place that must be removed. Then you are able to remove the heater core. It is about a $35.00 item.


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.