Steering and Suspension
Nissan Maxima
Ford Windstar SE

How do you replace the inner tie rod on 2000 Nissan maxima?

151617

Top Answer
User Avatar
Wiki User
2011-09-12 21:00:18
2011-09-12 21:00:18

You need an inner tie rod tool. Looks like a pipe with a drive socket on one end, and a receiver on the other. Unbolt the outer tie rod from the knuckle, and loosen the lock nut on the rod.

Either use a puller to remove the outer end, or hit the knuckle with a hammer, and remove the outer end from the knuckle. Unscrew the outer from the inner rod.

[break the lock nut loose before removing the outer from the knuckle, or you will not be able to loosen it]

Remove the bellows from the rack and inner rod.

Use a drift or punch and a hammer to push the lock plate off the inner rod end.

Place the correct adapter over the inner rod end, slide the rod inside the tool, and lock the receiver end of the tool on to the adapter. place a ratchet on the drive end of the tool, and remove the rod.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

what year maxima? 1989-1994 on the bottom.. 1995-2000 in the middle..

User Avatar

where is tcm censor located on 2000 Nissan maxima

User Avatar

Yes, the 2000-2001 Nissan Maxima is equipped with a fuel pressure regulator.

User Avatar

I have recently replace my starte for 2000 nissamn maxima gle and it cots around 500 usd with parts and labor.

User Avatar

How hard is it to change a 2000 Nissan maxima fuel filter

User Avatar

The entire bottom panel (5 bolts) has to be removed in order to replace the light.

User Avatar

The 2000 Maxima holds 9 qts or 8.5 liters

User Avatar

It will fit if the 2000 engine is a 3.0 L VQ30DE-K. They are almost identical engines

User Avatar

i have the code p0403 in nissan maxima 2000 i want to know how i can fix

User Avatar

Just pull it out by the two slots under the vent ajusters.

User Avatar

Your 2000 Nissan Maxima 3.0 liter V6 has a timing CHAIN(s)

User Avatar

how do you replace a bulb in a fog light on a 2000 maxima?

User Avatar

It must be a timing CHAIN because the Gates website does not list a timing belt for the 3.0 liter V6 in a 2000 Nissan Maxima

User Avatar

My 2000 Maxima gets about 25 MPG, 50% highway 50% local.

User Avatar

The average cost to repair a 2000 Nissan Maxima clutch is $600. The clutch will cost approximately $75. The labor will make out the rest of the cost.

User Avatar

The capacity of oil in a 2000 Maxima is 4-1/4 qts or 4.0 liters

User Avatar

For example a 2000 Nissan Sentra and a 2000 Daewoo Laganza are the same heater core but the Maxima is not..............

User Avatar

go here: http://maxima.theowensfamily.com/tsb/NTB02-051a.pdf

User Avatar

Just did one on a 2000 which is the same thing. You have to use an impact wrench with enough torque to take it out.

User Avatar

I have 1997 Nissan Maxima. You ned to replace the entire hub assembly. My problem is that they discontinued the 1997 hub assembly and the suggested replacement part's ABS ring is 4MM taller therefore the ABS sensor cannot clear the ABS ring. Any ideas on this one?

User Avatar

The 2000 Nissan Maxima transmission pan bolt torque specification is 60 pounds. The transmission pan bolt should be torqued in 30 pound intervals.

User Avatar

To disable the anti-theft in a 2000 Nissan Maxima, put the key into the ignition, but only turn it halfway. Leave it in this position for several minutes and start the car.

User Avatar

Applied to : 2000-2002 Maxima P1167 (Bank 2) Ho2S2 (Rear) (High Voltage Monitoring) Replace Oxygen Sensor... Check out this site..http://www.nissanhelp.com/Ownership/Bulletins/Nissan/2002/NTB02-051.htm


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.