When we replaced ours we used a hammer and chisel to remove the original sleeve in order to install the new polyurethane sub-frame mounts. I found them online at www.thezstore.com. Apparently the original rubber ones required the sleeve and the replacement ones don't. We found this out by searching for images to verify this informationSubframe Bushing Kit, 84-89 300ZX.Quantity in Basket:none
I hope this helps and you are able to enjoy your z car more!
you will have to remove the wheels/ rotor and hub assembly , buy a set of new axels from Nissan or after market auto parts and replace the old ones..not recommended unless you have knowledge on suspension work
Soak it in lube.
Can figure out how to remove rear rotor assembly to replace wheel bearing assembly on a Maxima 2004 Nissan
Remove the taillight assembly to gain access to the bulbs
I have 1997 Nissan Maxima. You ned to replace the entire hub assembly. My problem is that they discontinued the 1997 hub assembly and the suggested replacement part's ABS ring is 4MM taller therefore the ABS sensor cannot clear the ABS ring. Any ideas on this one?
Figured it out. OPen the Tailgate and look!
go to back of headlight assembly and twist it out.
In most cases when switching from Electronic to standard suspension you need to get the complete assembly from a non electronic suspension and put it it. This will work in MOST cases because the car body itself doesn't change only the suspension unit.
Go to the in side of the bed and the are two screws and the it pop off
No, just replace the bearings and the race.
You must replace entire assembly. If your problem is just foggy lenses, you can get lens cleaning solution at auto parts store.
To replace the headlight bulb in a Nissan Pulsar a person must first find the headlight assembly which is slightly behind the lamp housing. Once the headlight assembly is accessed, all an individual would have to do is loosen the bulb a half turn and the whole thing comes out, then replace with the new bulb using the reverse method.
wow i started to read this then said it was boring so i bought some shoes and me and my friend changed to this so i hope this helps with your question "HOW DO YOU REPLACE MIRROR ASSEMBLY ON A 2000 NISSAN PATHFINDER SPECIFICALLY PASSANGER SIDE" P.S IM DISLEXIC
My daughter has a 2002, and you must take it to the dealer, so we were told.
To replace the thermostat on a 1987 Nissan pickup, drain the radiator. Locate the thermostat which is under the top hose assembly, and remove the screws holding it in place. Put the new one in position and refill the radiator.
If you remove the panels from the interior of the trunk you should find the bolts that hold the taillamp assembly to the body of the car. Simply remove the nuts and this releases the lamp assembly.
there are two screws or bolts that hold rear light assembly located on inside of bed (10mm wrench) remove these and the complete light assembly comes out. do not remember which light is taillight but which ever one isn't working is the one you replace. There are 3 bulb retainers in the rear light assembly. Turn whichever bulb retainer you need to replace counter clockwise and it will come out and bulb is then accessible. If you are having constant problems with this, you may have the same problem I had and there is a recall on taillight assembly and Nissan will replace it for free. just had mine done.
Where can you get a Dash Assembly diagram for a 1997 Nissan Quest Van?
you must pull out the entire breather assembly, then you unscrew the housing. Next, flip the retaining clip and replace the radiator.
I had to replace the whole blade assembly. The rubber blade did not come off. The replacement blade from autozone came with the whole assembly. Cost wasn't much more than just the rubber blade style.
How do you replace 2003 nissan maxima headlight?
how to replace an altinator in a 2005 nissan altima
The rear universal joint on a 1998 Nissan Pathfinder should be replaced when it becomes worn out or broken. Symptoms of a worn joint include rough handling and suspension issues.
Could be a number of things, make sure you check your suspension parts eg. Tie rods,etc. If the noise is progressivly getting worse and lifer it could he your wheel bearings in which case you will more than likely need to replace the spindle assembly
replace coil springs in a nissan 300zx