Turn the ignition to the "ON" position without starting the vehicle. Press the gas pedal in 3 times, holding it in for 2 seconds each time. When the "Change Oil" light flashes, start the vehicle.
take the neg battrey treminal off for like an hr
Make sure the car is off. Turn the car on (not started, but "on") and IMMEDIATELY hit the gas pedal three times. I know it sounds pretty stupid, but that's how you do it. You may not get it the first time, so you may have to turn the car off, then on again.
How do I reset the service engine light on a 2003 Chevy Trailblazer?
AnswerIgnition on - engine off - floor the gas pedal 3 times. That's it!
When you change the battery you automatically reset the PCM. Any time you remove the negative battery cable for about 15-20 minutes you will reset the PCM. This will reset your Check engine light also. www.trailvoy.com Trailblazer enthusiasts forum with all the answers for your Trailblazer.
If you don't have a code reader you can disconnect the battery cable for a couple of minutes and that will reset the light
disconnect the battery
Turn ignition on (do not start engine), depress the accelerator to the floor 3 times within 5 seconds, change oil light should flash 5 times, done.
To reset your oil light:Turn the key to the 'on' position (do not start the truck).Press the gas pedal to the floor three times.
The best and fastest way to reset the instrument panel of 2004 Trailblazer is to disconnect both battery terminals. Reconnect them after about 30 minutes and everything should be reset.
ignition on - engine off - floor the gas pedal 3 times. That's it! LOOK IN YOUR OWNERS MANUAL!
Insert key in the ignition, then turn the key to on position without cranking, then push gas peddle three times within 5 seconds.
Turn the key on, engine off. Hit the gas pedal to the floor 5 - 6 times. shut the key off. It's now reset. Only reset it when the oil is changed.
Get the Trouble code read then have it reset at the same time. You can also disconnect the negative battery terminal for 10 minutes and it will reset. If you have not fixed the problem the code will set again causing your check engine light to come back on.
With engine off. Turn key to on. Press accelerator fully three times. This should reset light.
Any code setting for the radio must be done at the dealership.
The easiest way to reset the ABS light in a 1992 Chevy Lumina is to disconnect the battery for about 30 minutes. When it is reconnected, the light should be reset.
Turn ignition key to "run" (don't start) and press the gas pedal 3 times within 5 seconds.
most likely needs and oil change or you didn't reset the oil change light after you got an oil change. The truck has a standard that automatically cuts on the oil light either when the oil is low or you have driving a certain distant and not had an oil change. Also if you have had an oil change recently and didn't reset the oil indicator than it doesn't recognize that you did get an oil change. To reset oil indicator all you do is turn the key to the run position (two click, do not start truck) then pump the gas pedal all the way to the floor three times the oil light should flash then go off.
How do you reset check engine light for the 2009 Chevy trail blazer?
Press and hold the enter/select button for 3 sec. until it resets.
Reset the change oil light on Mazda 3
Read in your manual about the oil life management system. It says to wait for the light then reset it after the change. We have lots of reading on the subject at our enthusiasts forum www.trailvoy.com
When you take your car in for an oil change, have the technicians there do the reset for you. (they should automatically do that for you, but you may have to ask them....to make sure they do it) Valvoline does it as part of their service.
A code reader that can plug into car's diag port can reset it, there is no point resetting anyway without repair or it comes back on and could be something serious so find out what the problem is.
Key on engine off, press gas pedal to the floor three times, cycle key off and back on.
Lock the truck with remote then unlock truck manually with key