I am afraid I don't understand. If you are talking about reseting as in to set a new speed, turn it on, or turn it off, etc, all the function controls are on the steering wheel. Beyond what is on the control buttons, there is nothing else you can do. All control functions are there. If you have a cruise control that is not working, then there is no reseting it. You have some kind of failure that needs to be diagnosed and repaired. Something is broken.
I don't know about a reset, but there is a Fuse identified as CRUISE (Cruise Control Steering Column Controls) located in the Driver's Side Instrument Panel Fuse Block. See page 5-95 in your "Owner's Manual" for details.....
The three buttons on the right side of the steering wheel are your cruise control buttons. On, off, and reset.
Tap your brake. It suspends the cruise control until you hit resume
how do you reset the anti-theft system on a 1999 ford windstar
Press the 1 and 3 buttons on the head unit at the same time
The fuel pump reset button on a 2003 Ford Windstar is on the driver's left foot area. It is next to the hood release.
shut off the speedtronic limiter with the button at the end of the cruise control stalk
Push the reset button just to the right of the trip odometer
my side doorlock not warking what i do
On the turn signal lever, slide the cruise control switch to on with thumb(there are 3 possitions here, off, on, reset slide in that order). Drive up to the desired speed and press the signal lever on the center with your index finger, this will set the speed. When safe, release pedal and feel for reaction from the car itself. The Camaro will slow down slightly but will almost immediately regain speed if the cruise control engaged properly. Pressing the brake dis engages the cruise control. Sliding the switch to reset will reset the set speed and in the camaro this may come as a shock if the vehicle has much speed to make up like from 40 mph to 80. Be careuful.
Basically get the emission code at the repair shop, get it fixed, and reset the code. Some codes in Subaru involve Cruise Control light flashing. In my case, that happened due to a misfire on 3-rd cylinder (replaced the ignition coil), and EVAP system leak (bad fuel pump gasket). In both cases, after the repair has been done, the code was reset, and the cruise control light never blinked after that.
how do you reset change oil light on chrysler grand voyager minivan 1997
1) turn on cruise control (a light should turn on somewhere) 2) increase or decrease speed to desired mph 3) press button or apparatus to set or reset cruise 4) take foot off gas peddel and the car should maintain steady speed. I've had 2 VW's and the cruise didn't work in either one....perhaps your cruise just doesn't work.
Were is the antitheft switch
Chrysler does not use inertia/reset switches
The only way to completely reset the anti theft system on a 1999 Ford Windstar is to unhook the battery for 45 minutes. Once you hook the battery back up, the anti theft will be reset and any warning lights will be off.
reset Throttle Control Actuator of Nissan / my scanner g-scan and diagun i can reset with this tools or no
I don't think you can............try cutting the wire connecting to the battery
airbag warn light doesn't come on at all
ACC is an acronym for Automatic Cruise Control. If you are getting an "ACC Reset" Message, you can try cleaning the sensors, or try pulling the ACC fuse and leave it out for about 30 minutes of drive time and replace the fuse. That mat reset the ACC in the computer.
unhook the positive on the battery for 5 min. This should reset your check engine light if it doesnt then you still have issues.
Turn ignition on, go to where it says service exceeded. Hold in the reset button for about 4/5 seconds till it says Do you want to reset the interval, then press and hold the reset button again until a signal sounds. The reset button is behind the indicator an cruise control stalks on the dash (black pointy button). Its in manual on page295
If the anti-lock braking system light will not go off in a Dodge minivan, it can indicate a problem with the brakes. It can also just need reset by the dealer.
Contact the dealer, There is a certain procedure you have to go through.
on the floor on drivers side, left of brake pedal