If you mean by "timing gears", putting on a new timing belt then it's easy: The top sprocket has a line etched in it. This line should be at 12 o'clock. The bottom pulley also has an etch on it also, this should be lined up at the little black pointer (located about 2pm). The trick is to tighten the belt so that when it's tension is correct, the top sprocket is set at 12pm and the bottom pulley line matches up with the black pointer.
One thing to add to get the belt on you have to loosen the three Allen head screws that hold the water pump in and turn the assembly in order to get the belt on and then twist it back to take the slack out of the belt. Once you do this reset the screws and you're done.
IT'S IN THE HOUSING BEHIND THE TIMING COVER THAT THE UPPER RAD HOSE CONNECTS TO.
Neither its a gear set. Well depending if you have the 2.2 Ecotec or the 2.4 QUAD DOCH. Those engines have timing chains. The 2.0 has 2 gears. one on the crank and one on the cam. The others both have timing chains because they are DOCH 16 Valvers
there is 3 marks on the timing chain. 2 are exactly 16 links apart and the other is 22 from either of the 2. the engine should be at top dead center. line the 2 (16 apart) marks with marks on your cam gears and the 3rd with your crank gear. torque cam bearings to 100 inch lbs.
How do you reset the Toshiba studio 16 printer function
Its has a timing belt (2.0l 16 valve dual cam ) and a timing chain in rear of camshaft.
It has 16 forward and 8 reverse.
The lifters are underneath the camshaft, they sit on top of each valve, if it's 1.9 liter engine. You must remove the cam, or cams, cam gear ('s). Make sure you make sure the timing chain stays on the exact teeth of the gears, if removing the cam gears. The lifters sit on top of each valve, 8 or 16.
Where are the timing marks on a 1992 Toyota Paseo 16 efi 1.5 liter engine?
A timing light and a 9/16" swivel socket to loosen the distributor.
you have a timing belt its be-hin the cover
you can actually go to Kohlers website and download a manual for free that will walk you thru step by step how to do this. Their website address is www.kohlerengines.com You can buy one a a kohler repair center I believe it is a part # tp-2379, or old number of ens-575 It is actually pretty complex without the timing gear tool, there are marks on both the balance gears and crank gear and its a matter of counting teeth on both the timing gear and crankshaft gear. There are two styles of timing gears and the procedure differs for each one. follow the directions very carefully. Alternately, they can simply be left out of the engine without ill effect, most 12 hp and under do not use them but the 14/16 hp units all have them
Just really want to know the timing belt settings please?
when to chang timing belt on peugeot 407 hdi 1.6
do you mean firing order or timing? firing order is 1,3,4,2 timing is 16 degrees =/- 2 btdc @ 750 rpm =/- 50
Reset - 2008 was released on: USA: 16 August 2008 (48 Hour Film Project)
On the stator cover on the right side of the engine. Their will be a 9/16" bolt at the top of the housing, which is your timing hole.
there is no " timing belt " sensor, but there are 2 sensors that control the timing. One is the crankshaft sensor and the other one is the camshaft sensor.
the driving age is 16 i like the driving age because when your like 11 your getting into lots of crashes and your 16 you will know the gears and then you will know how to drive
Timing on 1997 pontiac grand am 2.4
on top of the computer you should find a wiring harnes one of them dose not have a end. and that is war you plug it in. on the right kick panel.
The timing marks, on your Mitsubishi engine, can be found on the front main pulley. The timing marks will be on the outside edge of the pulley.
16 degrees before top dead center
The 1996 Geo Tracker 1.6 liter engine timing marks can be found on the outside of the main pulley. The timing marks will be scattered around the pulley.
Oh about 16 feet Oh about 16 feet
The 1995 Toyota Camry four cylinder engine timing marks can be found on the main pulley. The timing marks will be scattered around the outside of the pulley.