0
I presume you are talking about how to change the direction of rotaion on an electric motor. To change the direction of a three phase motor, switch any two wires of the three phase feed, and the motor will rotate in the opposite direction.
Wiki User
∙ 14y ago
Wiki User
∙ 12y ago- It must be mounted in a set of bearing and bolted down to keep it stationary.
- Then a coupling must be installed on the drive end.
- A prime mover with a mating coupling must be installed and bolted to the shaft coupling. With the right lever, it can also be hand-cranked in order to rotate it.
Add your answer:
Earn +20 pts
Construction of anemometer?
An anemometer consists of 3 or 4 cups attached to a rotating shaft by thin rods. When wind blows, the cups and the shaft rotate. The speed of the wind is read using a meter similar to a car's speedometer attached too the shaft.
What will happen if you pass ac current passes through a inductor?
magnetic flux will be induced its use to rotate the shaft or given some force
What are the uses of footstep bearing?
A footstep bearing is essentially a cast-iron block with a gunmetal bush that has a hollow collar fitted on its top. This bearing is used to keep the shaft upright in a vertical position. The shaft is fixed in place and not allowed to rotate by a pin.
How does a turbo blower work?
turbo blower is an equipment where a turbine is attached with the blower part. steam enters through the turbine inlet and expands through the blades and goes to the outlet which helps the turbine shafts to rotate. this turbine shaft is attached with the shaft of blower that makes the blower rotating.
Why do you join two electric motors with a shaft?
easy, mount two in frame, place layshaft in middle with bearings, and collars to secure. Imagine a shaft that runs at the side of one, with gear on end, then rotate image in your head, and place another motor in , and wire up in opposite rotational direction. rc model guys do it on small scale, google it. steve
How do you axle shaft rotate?
Because the gearbox turns it
Do stihl trimmers rotate clockwise or counterclockwise?
ALL Stihl straight shaft trimmers rotate counter clockwise. ALL Stihl curved shaft trimmers rotate clockwise. This info is found on the Stihl FAQ page.
What is energy transfer used for?
To rotate the shaft and torqued the vehicle
What is an overdrive gear?
A gear which causes the transmission output shaft to rotate at a higher speed than the transmission input shaft.
How do you lubricate the shaft of a Stihl FS-46 trimmer and what lubricant?
To lubricate the shaft of a Stihl FS-46 trimmer, apply Reynolds lubricant to the shaft. Rotate the shaft and pull the converging wedge between the shaft and the bearing.
Why does the distributor shaft on your 1991 dodge spirit not rotate?
broken timing belt
What is being done about wind energy?
The blades spin, and then the main shaft, gear box, brakes, and high speed shaft rotate. This generates electricity.
What makes vertical pumps not working unless you rotate the shaft first?
Bad Motor Start Capacitor
Which part does not rotate when the engine is running and the clutch is depressed?
Clutch disc, pressure plate, transmission shaft,
Construction of anemometer?
An anemometer consists of 3 or 4 cups attached to a rotating shaft by thin rods. When wind blows, the cups and the shaft rotate. The speed of the wind is read using a meter similar to a car's speedometer attached too the shaft.
What does a drive shaft typically do?
A drive shaft is found in a frnt-wheel drive vehicle. It runs from the engine and gearbox to the front wheels. The engine generates energy, known as torque. The drive shaft carries the torque to the wheels forcing them to rotate, thus moving the vehicle.
What is the function of the differential unit of a car?
It allows the two axle shafts in the axle to rotate at different speeds, e.g., such as when the car is making a turn, the outer axle shaft will need to rotate faster than the inner.
