0
Try changing or cleaning out the stepper motor, this controls the idle and is a common fault on the 306.
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
How do machines make work easier?
A machine makes work easier by changing at least one of three factors. A machine may change the amount of force you exert, the distance over which you exert your force, or direction in which you exert your force.
What is links in HTML?
alink is an active link.. so how you would view a link, without mousing over etc. You can change the properties of this alone rather than changing the proper of the a class (which is how the link would appear when active, visited, moused over) this is more specific..
Hydroelectric power is produced by?
Water piped downhill from a reservoir to create considerable pressure, drives turbines connected to alternators that generate the electricity. That is then transformed up to transmit it over long distances at high voltages hence low currents, for efficiency. ++++ [Original answer is: ] This is a small version you can build by yourself. The water pushes a wheel, the wheel has a gear on the side of it mounted to the axle or pivot point. The larger the gear the better. The gear has a belt like one in a car engine. The belt attaches to a spindle on an alternator. The wires coming from an alternator run to a battery bank and will charge the batteries that are daisy chained together. From the batteries, it is recommended you have a power converter so you don't push too much power through the electrics you are powering. As long as the water is pushing the wheel the alternator will charge the batteries and provide power to your electronics.
How do you replace a light bulb that is over the stairs and can't be reached with a standard step or extension ladder?
Use a bulb changing tool. Basically it's a bulb holding device attached to a long or telescoping pole. Just do a search for " light bulb changer " and you will see that there are many to choose from. The home center stores carry them also.
What is the process of gear cutting in a horizontal milling machine?
The basic process of cutting gears on a horizontal milling machine:The operator makes sure the machine is off and leaves it off at this point. He also checks the coolant and oil levels and cleans the machine if necessary.The milling machine head is removed and the overarm is extended over the bed.A milling cutter (selected according to the profile of the gear tooth) is installed on the arbor and centered with spacing sleeves. It is then inserted into the spindle and fastened.An arbor support is slid into the overarm and over the arbor, then fastened.On the table of the milling machine, a dividing head is placed and fastened to the bed (to the left of the arbor and its chuck facing toward it). The billet (workpiece) to be cut into a gear is gripped in the chuck of the dividing head. The dividing head is locked.The operator makes sure no feed levers are engaged and the spindle is in neutral.The machine is switched on, started and warmed up.After the machine is ready it is stopped and the correct speed and feed for machining the gear is selected.Before starting the machine, the table is moved so the workpiece is below the cutter and the workpiece is centered to the cutter along its Y-Axis.The machine is started again and the operator touches the workpiece with the rotating cutter then zeroes the Z-Axis dial on the vertical feed crank.The table is moved to the left along its X-Axis so the workpiece clears the cutter and the table is lifted a few millimeters for the first cut.Coolant is turned on and the X-Axis feed is engaged towards the cutter enabling the cutting of the gear groove.When the groove is complete, the table is lowered and moved to the left again to clear the cutter, then lifted to the same amount as the last cut.The dividing head is indexed and rotated to the next groove position, locked, and the cutting process is repeated until all the grooves are cut. This process can be repeated several times depending on the depth and size of the gear grooves and only a fraction of a millimeter will be left for finishing.The operator will ensure the cutter is still sharp and in good condition before commencing with the finishing cuts.A pre-finishing cut is taken and the groove depth and profile is measured. If all is fine, the table is lifted to the final cut depth and the cutting process is repeated until the gear is finished.Once the gear is removed from the machine, the sharp edges are removed.The above method is just a basic explanation of how the operation is achieved. Operating any machine tool without proper training is not recommended and could lead to serious injury!
Why is my peugeot 106 over revving whilst I'm driving?
because the head gasket has gone
How do you stop a peugeout 206 over revving when changing gear and when stationary?
I suspect your autochoke is faulty, I has a similar problem a few years ago on a different car, but the symptoms were the same, it's a garage job I'm afraid
How do you stop your espace over revving?
over revving espace 1995 2000lilte
What could be the problem of a 1993 Chevrolet lumina 3.1l engine be if at high rpms the engine revs up and down?
Try locating and testing or changing the TPS (Throttle Position Sensor) Or if it's not in gear it could be the rev limiter keepin you from over revving & blowing your engine.
How can i change from first gear to third?
Changing gears is easy. All you have to do is push in the clutch and then up and over to third gear.
Why is your lawn mower over revving?
The most common cause of engine revving is a dirty or clogged air filter.
Honda Civic 1989 over reving?
If a Honda Civic is over revving than there may be a problem with the ECU. One of the functions of the ECU is to prevent the engine from over revving.
Why wont my peugeot 806 x reg diesel start it just turns over?
Glow plugs nee changing!
What are the advantages of submersibles over scuba gear?
One of the major advantage of personal submersibles over scuba gear is you can't feel the changing pressure while ascending and descending.
What is the function of mechanical governor?
It keeps the engine from over revving.
How bad is revving your engine in neutral?
As long as the engine is at full operating temperature and you do not rev it beyond the red line, you more than likely will do no damage, but it is still not a good idea. Revving a cold engine will do damage for sure. Revving the engine can cause a sudden drop in oil pressure, cause the engine to over heat and it doesn't help the main crankshaft bearings any good as they and meant to be revved under a load(in gear).
Why is my ford focus over revving especially when changing gears and petrol consumption has increased?
possible over reving cause- Idle Air Control Valve bad My ranger did same, dont know if causes bad milage though
