0
How do you test for a bad ignition switch on a 2008 Saturn Vue?
Wiki User
∙ 9y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you test ignition module 1992 Saturn SL?
Switch parts with another 91-95 Saturn and drive both until completely warmed up to see which car displays any temperature sensitive problems.
Where is the obd2 connector on a 2008 Saturn astra?
for most Saturn's, the diagnostic test port was below the steering column and a little to the left.
How do you reset the oil change light on a 1995 525?
Switch ignition on connect LED test lamp between terminal 7 of the diagnostic connector and earth after 3 seconds 5 green LEDs will illuminate Switch ignition off.
How do you replace the ignition of a 1992 Lincoln Town Car?
To replace Ignition Switch, first you have to remove the old one. To do this you disconnect battery ground cable. Remove the upper steering column shroud by removing the five self-tapping screws. Remove tilt steering column lock lever, Remove lower steering column shroud, disconnect the ignition switch electrical connector, turn ignition switch lock cylinder to the "run" position, remove the two screws retaining ignition switch, and finally unhook the ignition switch from the actuator. Now to install the new one.Make sure that the ignition switch lock cylinder is in the "run" position. You can test for the "run" position by rotating the ignition switch lock cylinder approximately 90 degrees from the "lock" position. Hook up the ignition switch into the actuator. You might have to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes. Install retaining screws. Connect electrical connector to ignition switch. Connect battery ground cable. Check ignition switch for proper operation, including start and accessory positions. Also, make certain that the column is in the "locked" position. Then Install upper steering column shroud. Install the lower steering column shroud and tilt steering column lock lever.
I know its pins 7 and 18 or 19 to reset my oil light on my 325is do you know the correct pins?
Switch ignition on. Connect an LED test light between terminal 7 and earth. After 3 seconds 5 green LEDs will illuminate. Switch ignition off.
How can you test the ignition modual?
ignition module on what?
How do I reset the oil service light on a 1992 BMW 318i?
Unless you have an LED test lamp the cheapest option is to buy a re set tool from an accessory shop. If you have an LED test lamp Switch ignition on Connect LED test lamp between terminal 7 & earth of the diagnostic connector located on the vehicles inner wing After 3 seconds 5 green LEDs will illuminate switch ignition off
How do you test ignition coil on your Alero 1999?
1999 Alero how do i test ignition coil pack
How do you Test the Control relay fuse air conditioner 1993 Saturn sl2?
You should be able to switch the relay with the horn relay and then check to see if the horn works.
Where can one test drive Saturn Crossover?
A person can test drive a Saturn Crossover by visiting their local Saturn dealer. The person who is wanting to test drive the vehicle will be require to provide a legal driver's license before being allowed to test drive the car.
How do you replace the ignition key switch in a 1995 Ford F-150?
1)Insert the key and turn it to the RUN position. Do not start. 2)Insert a 1/8" drill in a hole in the trim shroud below the ignition key. 3)There is a retaining pin in the hole. Push upward and you will depress the retaining pin. 4)As you push on the retaining pin, pull out the ignition key switch from the steering column. 5)When reinstalling, turn the ignition key switch to the RUN position and depress the retaining pin with your finger. 6)Insert the ignition key switch into the steering column. 7) Make sure the ignition key switch is seated and aligned before you turn the key to OFF. This will let the retaining pin extend into the hole. 8)Test to make sure the key goes to all the positions.
How do you test ignition module 1989 Chevrolet G30 5.7?
get a testlight ground it to the battery and turn the switch on and check the hotwire coming out of the module Also if you can remove it from the distributor you can take it to a good auto parts store and they can bench test it for you.
