Auto Parts and Repairs
Starters and Ignition Systems
Ford Ranger
Ford F-150

How do you replace the ignition key switch in a 1995 Ford F-150?

676869

Top Answer
User Avatar
Wiki User
2015-07-15 19:09:42
2015-07-15 19:09:42

1)Insert the key and turn it to the RUN position. Do not start. 2)Insert a 1/8" drill in a hole in the trim shroud below the ignition key. 3)There is a retaining pin in the hole. Push upward and you will depress the retaining pin. 4)As you push on the retaining pin, pull out the ignition key switch from the steering column. 5)When reinstalling, turn the ignition key switch to the RUN position and depress the retaining pin with your finger. 6)Insert the ignition key switch into the steering column. 7) Make sure the ignition key switch is seated and aligned before you turn the key to OFF. This will let the retaining pin extend into the hole. 8)Test to make sure the key goes to all the positions.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

We are replacing the ignition switch on a 1976 ford F150 Need some help - give us directions

User Avatar

How to drill out ignition switch on 1985 ford f150?

User Avatar

The ignition switch is usually mounted to the steering column and is operated by a linkage rod. NOTE On column-mounted ignition switches, don't confuse the switch with the lock cylinder and keys. The ignition switch is not normally visible. On some vehicles, the steering column support has to be removed and the column lowered to find the ignition switch. On others, the switch is accessible under the dash.The ignition switch is operated by the key switch. Courtesy of Ford Motor Company. To replace the switch: * Remove the ignition switch wiring harness. * Unbolt it from its position. * Bolt the new switch into position. * Attach the witing harness.

User Avatar

quiero saber si la troca F150 1995 tiene aigre a condisiado

User Avatar

The ignition switch is usually mounted to the steering column and is operated by a linkage rod. NOTEOn column-mounted ignition switches, don't confuse the switch with the lock cylinder and keys. The ignition switch is not normally visible. On some vehicles, the steering column support has to be removed and the column lowered to find the ignition switch. On others, the switch is accessible under the dash.The ignition switch is operated by the key switch. Courtesy of Ford Motor Company. To replace the switch: * Remove the ignition switch wiring harness. * Unbolt it from its position. * Bolt the new switch into position. * Attach the witing harness.

User Avatar

The ignition switch is usually mounted to the steering column and is operated by a linkage rod. NOTE On column-mounted ignition switches, don't confuse the switch with the lock cylinder and keys. The ignition switch is not normally visible. On some vehicles, the steering column support has to be removed and the column lowered to find the ignition switch. On others, the switch is accessible under the dash.The ignition switch is operated by the key switch. Courtesy of Ford Motor Company. To replace the switch: * Remove the ignition switch wiring harness. * Unbolt it from its position. * Bolt the new switch into position. * Attach the witing harness.

User Avatar

The ignition control module for a 1995 ford f150 is an important part of the drive train. If the module is failing then the engine will run erratically or not start at all.

User Avatar

multifunction switch in the steering column

User Avatar

Put an awl in the small hole under nieth of ignition switch,push up, with the ignition in the run position with vehicle off. Pull out in same positon and install new one in the run position.which is same position you will pull out old one.

User Avatar

do you want to know how to replace the ignition switch, which is not visible, and is the electrical part lower down on the column, or do you want to know how to replace the ignition lock cylinder, where you put the key in? *another thing to remember is that there was a recall on that part of an 89 f150. you can get it fixed for free at any ford dealership.

User Avatar

Replacing the ignition switch actuator on a 1988 Ford f150 is a complicated and multi-step process. First, remove the necessary panels to gain access to the steering column. Second, remove the screws and bolts holding the steering column to the dash. Third, locate the ignition switch and remove the actuator rod, replacing it with a new one. Re-attach everything to the dash and replace the panels. If this does not work, or seems too confusing, it may be in one's best interest to seek out a professional mechanic.

User Avatar

Well you could ram a flat head into the ignition and turn it to the on position then take steps

User Avatar

The actual problem is the starter continues to turn after key is turned off and pulled out of ignition.

User Avatar

no. Make sure wiper is in "OFF" position before you turn off your car.

User Avatar

take off the distributor cap see what you find.

User Avatar

Ignition relay is probably shot. It is in the power distribution block in the motor comprtment.

User Avatar

how to relace a door jamb switch in a 1994 f150

User Avatar

I just purchase a f150 that needs a new ignition switch and the man at auto zone gave me directions with pictures and diagrams, I hope this is of some use. Good Luck!

User Avatar

TAKE A ALLEN KEY SMALL ONE AND RIGHT UNDER THE SWITCH IS A HOLE PUT IT IN THERE AND TURN THE KEY TO START POSITION AND PUSH THE PIN WIGGEL THE IGNITION SWITCH AROND IT WILL COME OUT

User Avatar

To hookup the solenoid switch on F150 pick-up 5.0 after replacing it, first connect a voltmeter or test light to the solenoid's S terminal. Make sure the starter receives voltage at that terminal when the ignition switch is in the on position.

User Avatar

take panel off under ignition switch.turn switch to run position.look up under switch you will see a little pin .push pin in and pull cylinder out.i just did this and it works.remove battery ground first

User Avatar

First of all disconnect the battery remove steering wheel , there is a round slot in the steering column you insert a rod in there it will release the switch ( be sure to remove negative cable or air bag can go off. You may have to twist the switch back and forth to remove


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.