The Enhanced Warning System (BeltAlert) can be enabled
or disabled by your authorized dealer or by
following these steps:
NOTE: The following steps must occur within the first
60 seconds of the ignition switch being turned to the ON
or START position. DaimlerChrysler does not recommend
deactivating the Enhanced Warning System
(BeltAlert).
1. Turn the ignition switch to the OFF position and
buckle the driver's seat belt.
2. Start the engine and wait for the Seat Belt Warning
Light to turn off.
3. Within 60 seconds of starting the vehicle, unbuckle
and then re-buckle the driver's seat belt at least three
times within 10 seconds, ending with the seat belt
buckled.
NOTE: Watch for the Seat BeltWarning Light to turn on
while unbuckling and off while re-buckling the seat belt.
It may be necessary to retract the seat belt.
The Enhanced Warning System (BeltAlert) can be enabled
or disabled by your authorized dealer or by
following these steps:
NOTE: The following steps must occur within the first
60 seconds of the ignition switch being turned to the ON
or START position. DaimlerChrysler does not recommend
deactivating the Enhanced Warning System
(BeltAlert).
1. Turn the ignition switch to the OFF position and
buckle the driver's seat belt.
2. Start the engine and wait for the Seat Belt Warning
Light to turn off.
3. Within 60 seconds of starting the vehicle, unbuckle
and then re-buckle the driver's seat belt at least three
times within 10 seconds, ending with the seat belt
buckled.
NOTE: Watch for the Seat BeltWarning Light to turn on
while unbuckling and off while re-buckling the seat belt.
It may be necessary to retract the seat belt.
The Enhanced Warning System (BeltAlert) can be enabled
or disabled by your authorized dealer or by
following these steps:
NOTE: The following steps must occur within the first
60 seconds of the ignition switch being turned to the ON
or START position. DaimlerChrysler does not recommend
deactivating the Enhanced Warning System
(BeltAlert).
1. Turn the ignition switch to the OFF position and
buckle the driver's seat belt.
2. Start the engine and wait for the Seat Belt Warning
Light to turn off.
3. Within 60 seconds of starting the vehicle, unbuckle
and then re-buckle the driver's seat belt at least three
times within 10 seconds, ending with the seat belt
buckled.
NOTE: Watch for the Seat BeltWarning Light to turn on
while unbuckling and off while re-buckling the seat belt.
It may be necessary to retract the seat belt.
There is not an individual fuse for the seat belt chime. Check your owners manual for the "enhanced saftey system" for a method to turn it off.
To turn off the seatbelt chime in 2006-2008 Dodge Rams and some other newer Dodge vehicles, follow this procedure: Get in the vehicle, close the door, put on your seatbelt. Start the engine, wait for the seatbelt light to turn off. Within 30 seconds of the light turning off, unbuckle and re-buckle the seatbelt 4 times, making sure the seatbelt light responds (turns on and off) each time you unbuckle and re-buckle the belt. Ending with the seatbelt BUCKLED, turn off your engine. If done correctly, you will immediately hear one chime to verify the programming. To re-enable the chime, simply repeat this procedure.
To turn off the seatbelt chime in 2006-2008 Dodge Rams and some other newer Dodge vehicles, follow this procedure: Get in the vehicle, close the door, put on your seatbelt. Start the engine, wait for the seatbelt light to turn off. Within 30 seconds of the light turning off, unbuckle and re-buckle the seatbelt 4 times, making sure the seatbelt light responds (turns on and off) each time you unbuckle and re-buckle the belt. Ending with the seatbelt BUCKLED, turn off your engine. If done correctly, you will immediately hear one chime to verify the programming. To re-enable the chime, simply repeat this procedure. NOTE: Although the seatbelt chime will not chime constantly if your belt is not buckled while driving, it WILL still chime when you first start your engine, and the seatbelt light will stay on to remind you. The light can be deactivated also, but it is a much more complicated (and I feel unnecessary) procedure. WARNING!!!: DO NOT deactivate the seatbelt chime by cutting or splicing the wires to the seatbelt buckle under the seat. THIS WILL DISABLE YOUR AIRBAGS even if your belt is buckled!!! AIRBAGS are DEADLY if your belt is not buckled, so there is a sensor in the buckle which disables the airbags when the belt is not buckled. If you cut or splice these wires, you also disable that sensor. Turning off the chime using the programming option keeps your airbags working properly. Hope this helps, ENJOY YOUR DODGE!!! -Mike Vidal, Forked River, NJ
By wearing your seat belt.
get an old seatbelt from a junk yard and plug in into the seatbelt soquit
Here is a couple of links to check out! One is a mechanical fix and the other is, well you decide :) http://www.tundrasolutions.com/forums/tundra/107489-diy-how-to-disable-seatbelt-chime/ http://www.tundrasolutions.com/forums/tundra/135468-diy-contest-seatbelt-chime-light-gone/
How do you fold the rear seats down in the 2008 dodge ram 1500 quad cab?
Yes, they will.
5 on 5.5"
Yes.
4x4, yes2wd, no.4x4, yes2wd, no.
5*5.5