You fit the Allen wrench into the socket in the centre of the motor shaft and turn it either way to dislodge the obstruction. Most disposals take a 3/16 inch Allen Wrench, but some may differ.
On the bottom of the disposal in the center there is a hex, 6 sided hole. A tool came with the disposal to use in this to unjam the disposal. It may be under the sink somewhere or you can use a regular hex wrench. Insert the wrench and wiggle it back and forth. Don't put too much pressure on it, just back and forth. You may be able to back it out of the spot it is in.
Good luck. On the bottom of the disposal, in the center there is a spot for using a hex wrench to turn the blades by hand. You may be able to turn it backwards while pulling on the cloth to get it out. If that doesn't work, you can try to tear as much of it out as you can and try to get it to go down the drain. Use the hex wrench again back and forth to try and dislodge the cloth. A wrench came with the disposal and my be under the sink somewhere. About 6 inches long in a flat S shape.
If it is a double sink, does the other side drain? Are you trying to fix the disposal because it does not come on or because it comes on but does not drain. If it comes on but does not drain and the other side does, it is probably just clogged with food. They make drain cleaners for disposals. If neither side drains, put the stopper in the disposal side, hold down on it and plunge the other side.
If you don't have a disposal, you can get a Tail piece, the section of drain right below the bottom of the sink that has a Y on it that is the size of the drain from the dishwasher.
If the sink/sink drain fitting connection, sink drain fitting/disposal connection, dishwasher/disposal connection, disposal/drain elbow connection are what are leaking they can either be tightened or have gaskets replaced or other sealing methods used. If the disposal is leaking elsewhere the disposal needs replacement.
You need to lie on the floor in front of the sink and look at the bottom of the disposal canister to see it. Or, use your palm to feel it. Your disposal should also have a small wrench that came with it.First, make sure the power switch on the wall is OFF and that no one is near the disposal. Second, press the reset button. Get up, turn the water on and see if the disposal works. If not, turn the switch OFF again. Read the manual to find the section about using the wrench. It should say to turn it in a clockwise direction---if unsure, call the manufacturer or a plumbing store to double-check. After turning the wrench, get back up and re-try the disposal with the water running.NEVER insert anything into a disposal except food scraps.NEVER put a wooden spoon, long tool, or your hand/arm into the disposal to free the blades!Once you get it going with the reset button and wrench tool, you can dump in a half cup of ice, along with 1/4 cup of Baking Soda, followed by more ice. Turn on the disposal and let it grind the ice while running warm water through the disposal.Other people use small cut lemon slices to freshen the disposal.
The sink drain is blocked somewhere after the disposal. take apart and clean or renew sink drain.
As long as the drain basket for the disposal will fit the drain hole in the sink, there shouldn't be a problem
The disposal is clogged or that side of the sink is.
A garbage disposal is a convenient tool for virtually any kitchen, and once the appliance is in use every day, it is hard to do without one. There are a few things that can cause a garbage disposal to go on the fritz and some of them can actually be fixed without calling in a professional.No NoiseIf the disposal has stopped making any noise when it has been turned on, there are some things that can be checked.1. Look under the sink, at the bottom of the garbage disposal, and try to press the unit's reset button. Sometimes it is as simple as the reset button popping out. Push it back in and give the disposal another try.2. Check the circuit breaker. If it has been tripped, switch it off and back on, then try the disposal again.3. Find the switch that powers the garbage disposal. This is usually located on the wall near the sink or in the cabinet underneath the sink. It may be a case of a malfunctioning switch. Turn off the circuit breaker the powers the disposal, then replace the faulty switch. Try the disposal once again. If this is an uncomfortable situation, it might be worth it to have a professional fix it.4. If nothing else is fixing the problem and the disposal still makes no noise when turned on, it might need to be replaced completely. A bit of do-it-yourself knowledge is required for this sort of replacement, so a professional might be needed.Strange NoisesIf the disposal unit is making odd or humming noises but will not actually run, it might be clogged or stuck on something.1. Switch the circuit breaker that powers the disposal off.2. Most garbage disposals come with an offset wrench. Insert this wrench into the flywheel turning hole - this is situated on the bottom of the garbage disposal. Going in a clockwise direction, turn the wrench. This will dislodge anything that has gotten stuck. The flywheel will turn freely when it has been cleared.3. Never put a hand down the garbage disposal. Using a wooden broom handle, the disposal's impeller can be easily unclogged or unstuck from the sink drain. Place the end of the handle against the impeller and, using a bit of elbow grease, try to free it. When it is not obstructed any longer, remove the handle and push the reset button underneath the unit.4. Turn the water on in the sink and quickly switch the disposal off and on for a few seconds. This will make the flywheel spin and can help to dislodge anything clogging it.
No, you do not need a special garbage disposal for a porcelain sink. However, generally speaking, installing a garbage disposal under porcelain can definitely damage the porcelain texture.
There is probably a reset button on the bottom that may be tripped. Just push it in. With the disposal off, you can use a wooden broom handle in the disposal to rotate the blades and free them. On the bottom in the center, there should be a place for a 6 sided hex key that will rotate the blades. There is usually a key with the disposal that may be under the sink somewhere. About 5 inches long in a flat S shape.