0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you wind a bobbin on a Sew Gem sewing machine?
Singer has manuals for many of the White models on their web site.
How do thread a bobbin on a singer golden touch and sew model 620?
The bobbin is wound in the bobbin case. You open up the slide plate and push the little lever with the bull's eye on it all the way to the left. Then you thread the needle with the thread you want on the bobbin, then pull a few inches and wrap the needle thread around the knurled knob that holds the foot onto the shaft (to keep it from slipping.) Then you push down on the foot pedal and the bobbin fills from the needle thread. Don't overfill the bobbin or it won't wind out properly.
When was Young Mr. Bobbin created?
Young Mr. Bobbin was created on 1951-08-29.
How do you play wind the bobbin up on paino?
cegab
How do you thread and wind the bobbin for an American Home Deluxe sewing machine?
To wind the bobbin you thread the machine except for the hook above the needle and the needle itself and pull the thread over the notch at the top on the front. Start the thread on the bobbin just till it stays and then place it on the little post on the right side by the wheel and pull down the small lever just above the post and then press on the pedal and wind till the bobbin is full. I still haven't figured out how to thread the bobbin yet but it shouldn't be to hard.
How do you load a front loading bobbin?
I'm assuming you're talking about winding a bobbin on a sewing machine? If so, there is a post similar to the one for thread (near it) that you put the empty bobbin on. Then you put your spool of thread where it goes on the machine. You wind your thread from the spool of thread to the bobbin (there's usually a little chart on your machine, but if not, the thread goes through a hook or two and then you wind it about 4 times around the bobbin (clockwise). In newer machines you then push the bobbin toward a holder type thing that is near it. This disengages the needle from going up and down and lets the machine wind the thread as you push the pedal. On older machines, you have to turn the handle of the machine toward you and it disengages the needle, allowing the bobbin to be filled when you press the pedal. Hope this helps! You could probably google your sewing machine name and how to thread a bobbin and maybe get a diagram.
When was The Wind Singer created?
The Wind Singer was created in 2000.
How wind a bobbin on a singer touch sew 600?
Set the stitch width to #3, the stitch length to reverse, and the selection dial to AK (straight stitch). Open bobbin casing door by sliding it toward you. Remove old bobbin if necessary by lifting metal latch and simply pulling bobbin out. Place empty bobbin in bobbin casing (small disc side down) and replace latch. To the left of the bobbin casing is a tiny metal circular button that doesn't actually look like a button, it just looks like it might be part of the machine, push it down. If it is too hard to push then it might need a little bit of oil. Push it until it locks down. Keep the sliding door open. Okay, take a breath. : ) Thread the machine as you would normally would, instead of sliding the tail of thread under the foot, just thread the needle and gently wrap the tail around the knob that is on the left side of the foot just once,(the screw that allows you to change feet), continue holding the thread and now push the pedal at a moderately speed to wind the bobbin. Congrats, you did it!
How many pages does The Wind Singer have?
"The Wind Singer" by William Nicholson has approximately 416 pages.
How do you re fill a bobbin on the singer 6267 sewing machine?
First of all make sure that you have the correct bobbin for the 6267 machine. There are quite a few and not all of them will fill with this machine. Open the slide plate underneath the needle and insert the bobbin. PARTIALLY close the slide plate. The marks on the slide plate and machine bed must be lined up for the bobbin winder to work. Bring thread from needle under the presser foot. Wind the thread one turn in any direction around the presser foot screw. Press the "One Step Buttonhole A" button on the control panel. Begin running the machine Watch through the slide plate until the amount needed is reached on the bobbin. Stop the machine , remove the thread from the presser foot screw.. Close the slide plate completely.
Who was original singer of wind beaneath your wings?
Bob Montgomery.
What singer sang three sheets in the wind?
Johnny Bond
