0
How does a harmonic balancer loosen itself on a 97 Jeep Grand Cherokee 4.0 in-line six and which way does the bolt turn to tighten and can you re-tighten it with standard tools?
Wiki User
∙ 15y ago
Under normal circumstances it will not loosen. You use a torque wrench to tighten it to specifications. Specifications are located in the Haynes repair manual available from www.Amazon.com. clockwise to tighten counterclockwise to loosen You need a socket that fits tightly on the bolt head and a long-handled torque wrench.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
Can a Jeep Cherokee Standard shift be towed in neutral?
yes
Does the 2015 jeep grand Cherokee have front wheel drive or rear wheel drive?
Rear wheel drive is standard, all wheel drive it an option.
Does a 1994 Jeep Cherokee with standard transmission need transmission fluid?
Yes. The auto in a Cherokee uses Dextron.The manual uses 80w90.If it is a Grand Cherokee the auto uses Mopar ATF+4.Yes. The auto in a Cherokee uses Dextron.The manual uses 80w90.If it is a Grand Cherokee the auto uses Mopar ATF+4.
How many gallons does the gas tank in the 2008 Jeep Grand-Cherokee hold?
My 92 Cherokee Laredo has a 20 gallon tank according to the owner's manual (and a few trips to the gas station). The Haynes Repair Manual for Jeep Cherokee - 1984 thru 2001 mentions however, that there were some with 13.5 "Standard" and 20 "Optional". both above answers are correct. What I did was run the tank down to the yellow warning light and then some, you should still have 2+ gallons in there and then fill up...............Mike The Jeep Grand Cherokee in 2001 holds about 16 gallons. My 1996 Jeep Grand Laredo will hold 21.5 gallons, coasted into gas station once and it filled to this amount.
How do you put a the standard window latch on the vent window of a Jeep Cherokee?
if you mean how is it affixed/how to mount a new one - clean thoroughly, and use the same glue you'd use to mount a rear view to the inside fo the windsheild.
Is there a difference in the harmonic balancer from an automatic to a standard?
No there is not.
Are the threads on the harmonic balancer bolt for a 93 dodge Dakota reverse or standard thread?
Standard.
Are the threads on the bolt left or right thread where it goes through the harmonic balancer and in the crank on 1974 Chevy 350 c you engine?
They are standard right hand threads.
Is the bolt for the harmonic balancer on a Nissan 3.0L left or right hand thread?
The bolt is just a standard right hand thread. Just took one out of an '01 Xterra.
Which way are the threads on a harmonic balancer 1992 buick century 3.3 engine?
Normal. I just replaced mine and it is standard thread (righty-tighty, lefty-loosey). Us a 6 point 15/16 socket wrench. I used a breaker bar against the frame with the socket on the balancer bolt, hit the starter without starting the engine, and it broke the bolt loose enough to take it off. I had to use a pulley puller to get the old harmonic balancer off. It helps to take off the passenger side front wheel and the plastic panel for better access.
3.3 Buick century how to remove harmonic balancer?
1. Remove right front wheel. 2. Remove the cover from the inside fender. 3. Remove the small inspection cover between the engine and transaxle to expose the bottom of the flywheel. Jam a big screwdriver in a tooth of the flywheel and wedge it against the side of the opening and the floor or have an assistant hold it. 4. Use a big ratchet, at least a foot and half long and a cheater pipe another foot and a half to generate the 200+ foot pounds to remove the bolt from the center of the balancer. 5. Use a harmonic balancer puller to remove the balancer. A kit may not have the right size bolts to thread into the two holes in the balancer and you'll have to hunt for the right ones at a hardware store. They may be smaller in diameter than what come with the puller. Good luck. 2. The 3.8 Buick harmonic balancer requires a special puller. But, if you purchase three 4" long, 6mm diameter, 0.1 thread bolts and three heavy duty washers you can use a standard 3 hole puller to remove the balancer. The threaded holes for the 6mm bolts are about 2" inside the access opennings that are located on the face of the balancer. You will need to place the heavy duty washers on the 6mm bolts brfore they are used with the puller. The hex heads on the bolts are to small for the standard type puller and the washers will support the torque required to remove the balancer.
Where is the crank sensor on a 1993 Mitsubishi 3000 GT?
behind harmonic balancer,front of engine(passenger side of car is "front") balancer is large pulley down low - must use harmonic puller to remove- DO NOT use standard puller or you will destroy it (costs about $300.00 to replace)then also need to remove cam-belt cover
Is the crank bolt on the harmonic balancer of a Toyota 4 runner left or right hand threaded?
It is standard thread. Torque to 220 ft lbs. Apparently the keyway is deep inside barely protruding from the timing gear on the crank so you might have to push that gear back to figure out where to line it up. I have not confirmed that yet though since my balancer just fell off last night.
How do you set the timing on a Buick 3.8 engine?
the timing is computer controlled when there is no dist.---which became standard in 1987---previous to that you rotate the dist. and set it to the number of degrees advance that the decal under the hood says---some where around 10---the timing marks are behind the harmonic balancer (which is on the end of the crankshaft)
Harmonic balancer Buick?
I recently had my harmonic balancer replaced on my 1990 Buick Riviera. When opening the hood, I could actually view the part. It was located on the passenger side of the engine close to other pulley wheels. I googled the part and found it related to cutting down the vibration and stress which may affect the crankshaft. Be aware, I am not a mechanic or guru on vehicles. It cost me around $200 to replace which included the new part and labor. Hope this is of some benefit. BTW, I new something was wrong because it made quite a noticeable sound when starting and when it was in idle. The 3.8 Buick harmonic balancer requires a special puller. But, if you purchase three 4" long, 6mm diameter, 0.1 thread bolts and three heavy duty washers you can use a standard 3 hole puller to remove the balancer. The threaded holes for the 6mm bolts are about 2" inside the access openings that are located on the face of the balancer. You will need to place the heavy duty washers on the 6mm bolts before they are used with the puller. The hex heads on the bolts are to small for the standard type puller and the washers will support the torque required to remove the balancer. The puller must be the type that allows an extension rod to be added to the center bolt of the puller. This extension is needed because the center bolt of the puller is to large in diameter and it is not long enough to reach the back of the through hole on the crank shaft. (it is drilled very deep). Cost about $2.50, This beats paying over $150.00 for the suggested factory puller.
Can a Jeep Cherokee Standard shift be towed in neutral?
yes
Has the 1996 Jeep Cherokee xj limited slip diff?
Not standard.
