I have had two windows regulators replaced on my 1999 Chrysler 300M. There is a lot of precise calibration that has to be done so the window forms a tight seal with the weather striping but at the same time, the force pushing up the window can't be so great that the window breaks. Its best to have a certified machanic replace them.
To install a new window regulator on a MGRZ driver's door, remove the door panel and the wiring attached to the power window mechanism. Remove stereo speaker from the inside door and the window glass. Remove the old window regulator and replace with new.
Disconnect the battery.Remove the door panelRemove the power window motorRemove the regulator spring.Move the window down a bit and remove the two 10MM nuts from the window.Twist the window spring stud counter-clockwise.Now you should be able to remove the window regulator.
Remove the window regulator assembly from the door.Remove the motor from the regulator by drilling out the attaching rivets with a 3/16 in. drill bit.Connect the window motor to the regulator with 3/16 in. rivets.Install the window regulator assembly.
1. Remove the power window regulator2. Install a pan head sheet metal tapping screw through the sector gear and the backing plate at the hole provided to lock the sector gear into position. Then drill out the motor to regulator attaching rivets.3. Remove the motor from the regulator.To install:1. Lubricate the motor drive gear and the regulator sector teeth. Install the motor to the regulator and check the mesh of the motor to the regulator.2. Install rivets to the motor and the regulator.3. Remove the sheet metal tapping screw.4. Install the power window regulator.
Remove door panel, remove glass, take out old regulator ( if you need to remove rivets by cutting or punching them out you may use nuts and bolts to install new regulator), install new regulator and glass, ensure proper function, re-install door panel.
Complete instructions with photos:
To remove the drivers side window and regulator, you will need to remove the door panel from the door. Then you can unbolt the regulator and window to remove them.
First, remove the switch panel by prying it out and disconnecting the electrical?æconnectors. Pry away the trim panel so that you can get to the mechanical workings of the window. Remove the fasteners that hold the regulator to the door and then remove the regulator. Install the new regulator and put the door back together.
Which regulator and what year? You have a window regulator, voltage regulator, fuel pressure regulator to name a few.
Begin by removing the inside door panel. Remove the wiring harness from the electric window regulator. Remove the window regulator retaining screws.
You have to remove the door trim on the inside of the door. Also remove the window crank handle if it is manual windows. 1. remove the window regulator by unbolting the regulator from the door shell and sliding the window guide arms out of the window channels. 2. You then remove either side or both sides of the vertical window channel that the window goes up and down on. 3. Finally, most of the time you need to remove the window rubber seal that runs horizontally along the bottom of the window opening to get the glass and the regulator channel that is attached to the glass out of the door.
Usual issues are window motor, window regulator, switches & wiring
Remove the door panel. Use a coat hanger or ty rap to secure the window in the up position. Disconnect the wiring from the motor. Remove the bolts that secure the glass to the regulator. Remove the regulator. Install motor on new regulator. Installation is the reverse procedure. 6 to 8 bolts in entire process. Good Luck. CAH
First you need to remove the door panel.Then remove the door handle bracket.Peel back the moisture shield.Tape the window into place,then unbolt the window from the regulator.Remove the window regulator from the access hole in the door.
1 open door 2 remove inner panel 3 lower window 4 take out window 5 remove (4) screws from regulator 6 take regulator of rails
It is best to replace entire regulator as one unit. Remove door panel. Remove bottom nut of regulator, and remove two top nuts of regulator. Loosen two bolts on bracket holding window. Support window, and carefully remove regulator as one unit.
remove your door panel there will be three screws holding it on. then you have to remove the screws holding your window to the regulator. then unbolt regulator and motor from door. Undo wiring going to motor.
turn bolts to the left, install regulator, turn bolts to the right
Lower window at least a couple of inches if possible. Remove interior door trim panel. Unplug anything at trim panel. Unplug window motor. Remove 2 bolts holding glass to regulator. Tilt window glass forward, then remove upward and outward from door. Remove 4 or seven bolts and/or nuts mounting regulator and motor to door frame. I think it's 4. Maneuver regulator out of door frame. If 4 in above step, remove 3 bolts mounting motor to regulator, otherwise you'll be replacing the whole regulator. Install by reversing above procedure.
The cables are not adjustable. The regulator is only serviced as an assembly.
How to remove the window motor from the regulator
The window motor is attached to the window regulator by screws. After removing the door trim you must detach the regulator from the door by drilling-out four rivits. Then remove the screws from the old motor and install the new motor. Re-attach the regulator with bolts and put the trim back on the door.
u have to remove the drivers window and remove the regulator assy...once its out there ar 4 rivits u have to drill out be very carefull of th spring in the regulator it will come out and injure u if u don't take the proper precautions
First remove the door panel.Then remove the moisture barrier.Next remove the window motor from the window regulator.
remove back seat, remove screws bottom and top of panel, remove panel. remove 3 bolts and motor arm, window and regulator will pull out.