The lens can not be replaced alone, you have to replace the whole head lamp assembly
With lots of newer cars, only the bulb is replaced as opposed to the whole headlight assembly. Check and see if you can twist off the bulb from the backside of the headlight. Or, just go to any auto parts store and give them your car's make and year. When they find the product, simply ask them how it is replaced.
You have a broken wire.
Open the hood of the engine compartment to your 1994 Toyota Corolla. Remove the wiring harness from the headlight. Remove the headlight retraining bolts from the headlight assembly. Reverse the process to install the new headlight.
If you're talking about the headlight, the "lens cover" is not a separate part, you need to replace the whole headlight assembly.
My drivers lens is all sctracthed and fogged up and my . # vsibility is causing me proublems
The horn is located behind the drivers headlight. To remove unplug harness, undo bolt in bumper assembly behind drivers headlight (must be removed first), and it slides out. To install new, follow steps in reverse.
in the bottom of the washer fluid reservoir over the battery on the drivers side near the headlight assembly
The drain plug is on the drivers side of the radiator. It is almost straight down from the headlight assembly.
After you open the hood the whole headlight assembly can be removed by taking off the the two black plastic wing nuts on top holding the headlight assembly in. There is also another wing nut like bolt that is between the headlight assembly and turn signal assembly that must be removed. One you do this you have to lift up on the headlight assembly to clear the threaded studs that the plastic wing nuts were on and pull both headlight and turn signal light assemblies straight out. They both have to come out together. There are some clips that still hold all of this in, but it will come out when you pull it straight forward. I have done this several times and it seems kind of tricky the first time, but actually is pretty easy.
The horn is situated at the front of the engine compartment. The horn will be to the left of the drivers side headlight assembly.
Remove the headlight assembly to gain access to the parking light socket/bulb.
I need a headlight assembly for 87 Plymouth colt e. drivers side
Remove the plastic cover over the drivers side headlights, then remove the headlight assembly(driver side only). The horn is directly underneath it - fairly easy to access, remove, replace, whatever you need to do. I replaced mine in no time.
Gen 1 or 2? With the drivers side you will have to remove the battery and then the nuts to the lights, disconnect the wiring and remove.
To change the headlight assembly just loosen/remove the two bolts holding the entire light assembly in (side marker, headlight and turn signal)Also remove the screw located where the marker light and headlight meet. Once these are removed the entire assembly will shift to the right for the drivers side (when facing the vehicle) or to the left for the passenger side (when facing the vehicle). Once the assembly is removed you will have access to the wires/bulb. To ressemble simply do the reverse. hope this helps. "G"
If it's the same as my 92, you'll find it under the hood, drivers side just behind the headlight assembly.
I have a 1997 Plymouth Neon. The way to replace the headlight bulb is: 1. open hood, and disconnect the wiring connector from the headlight bulb socket. 2. Turn the bulb socket retaining ring counterclockwise and remove the bulb and socket assembly. 3. Pull the bulb out of the socket assembly. 4. Reinstall the bulb and socket assembly in the light housing. Turn the retaining ring clockwise to secure the bulb in the housing.
hmm seems to me that the the light assembly mabye bent or that the sighn that the ,motor is on its way out Is there a stop switch?
how do i replace the drivers side headlight in a 2003 oldsmobile silhoutte
check the ground wire to that headlight .
I can only speak for the 2nd model 92-96 it is located just inside the fender and can either be located behind the passenger headlight assembly, or the drivers side
More than likely you need to repair the headlight bucket section of the nosecone (either side of the grill) and /or replace the headlight assembly. It will take some fiberglass mesh and some resin and hardener .
The headlight relay on a 1999 Chevy Cavalier should be inside of the relay box. It is mounted close to the drivers side headlight.
If it is like a 2000 grand prix, just loosen/remove the two bolts holding the entire light assembly in (side marker, headlight and turn signal) Once these bolts are removed the entire assembly will shift to the right for the drivers side (when facing the vehicle) or to the left for the passenger side (when facing the vehicle). Once the assembly is removed you will have access to the wires/bulb. To ressemble simply do the reverse.