answersLogoWhite

0


Want this question answered?

Be notified when an answer is posted

Add your answer:

Earn +20 pts
Q: How long does a suzuki samurai fuel pump pushrod have to be?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Will a 2.5ltr jeep motor mount into a suzuki samurai?

yes, as long as you change all components to that for a Jeep


Where is the fuel filter on a 2004 suzuki aerio?

SUZUKI Aerio electric fuel filter and pumps are almost always located inside the fuel tank, and recommended a replacement after 240.000km. the advantage of this filter is require no maintenance as long there is no problems with the engine performance.


Where is the fuel gauge on a Vl250 SUZUKI?

The VL250 does not have a fuel guage. You can use the trip meter to judge how long before you need to fill the tank.


How much does a suzuki samurai motor weigh?

The g13 long block engine weighs 100 pounds The long block with intake carb etc fully dressed weighs 170 Http://www.sammypro.com


Will the 1.3 liter engine block from a 1988 Suzuki samurai be a direct replacement for the 1.3 liter engine block from a 1993 samurai?

OK, 1st off I can't give you a definitive answer...but I worked on older Samurai's A LOT, and they and early Geo Trackers and Sidekicks) had a lot of similarities... Short story: Lots of owners of earlier Samurai's converted them to fuel injection using parts from newer Samurai's...or converted them to 1600 cc setups using 8-valve Geo Tracker or Suzuki Sidekick engines. So having a newer Samurai setup and using an older block would be about the same thing, just into a newer rather than older chassis when you're done. There were 2 different 'short blocks' used in Suzuki Samurai's. One ended in letter 'a' the other letter 'b', and I think there was a VERY small difference in displacement...like the earlier one was about 1300 cc and the newer one around 1297 cc I think. But they were interchangable...I remember the 1st time I got a replacement engine for my 86 I was told by the machine shop that all the short blocks were essentially interchangable. Even new replacement pistons were the same for either block (or for that matter, for the 8 valve 1600 cc engines for trackers as well.) Hope this helps. Hope this helps. Clarification to my earlier remarks: They were related to a 'short block' not a 'long block'. The cylinder heads did change over the years between carburated versions and fuel injected versions, mainly by no longer having an eccentric off the back of the camshaft to drive a pin that went through a hole in the rear passenger side of the head to drive the mechanical fuel pump. Since fuel injected models do not use a mechanical fuel pump, this was no longer needed. You might still be able to use an older cylinder head on a newer engine, even if the newer engine is fuel injected, by removing the pin and blocking off the no-longer-needed fuel pump port. I think all Samurai's used 8 valve engines, unlike Geo Trackers and Suzuki Sidekicks that eventually went over to 4 valve per cylinder, 16 valve totals. An 8 valve cylinder head will NOT work on a 16 valve intake/exhaust port setup...


How does someone become a samurai?

Read "The way of the Samurai" found in almost all library's it's not very long but too long to answer here.


How long is the 2007 Suzuki SX4?

The 2007 Suzuki SX4 is 13 ft. 6.8 in. (162.8 in.) long.


How long is the 2009 Suzuki SX4?

The 2009 Suzuki SX4 is 14 ft. 9.6 in. (177.6 in.) long.


How long is the 2013 Suzuki Kizashi?

The 2013 Suzuki Kizashi is 15 ft. 3.1 in. (183.1 in.) long.


How long is the 2013 Suzuki SX4?

The 2013 Suzuki SX4 is 14 ft. 8.8 in. (176.8 in.) long.


How long is the 2011 Suzuki Kizashi?

The 2011 Suzuki Kizashi is 15 ft. 3.1 in. (183.1 in.) long.


How long is the 2010 Suzuki Kizashi?

The 2010 Suzuki Kizashi is 15 ft. 3.1 in. (183.1 in.) long.